i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi,When I use nRF Connect app(IOS version) to connect my ble device,BLE_GATTS_EVT_SYS_ATTR_MISSING log information appears in my RTT Viewer(Picture IOS_Phone_Conncet).After...
Hello,
I tried as you mentioned using sdk12.1.0 buttonless_dfu and bootloader_secure example.
I didn’t modify anything except dfu_public_key.c.
As shown in the attached...
Hello,
I have a program that do an infinite loop in sd_softdevice_enable. How can i investigate ?
Loop is from 0x00009DEA to 0x00009DF2
Target is nRF52832 AA with...
Hi,
I am working on nRF52 with freertos + SDK13.0 + sd S132_4.0.2. I found the device will be trap in the xTaskIncrementTick of the xPortSysTickHandler when some task is...
Hi Nordic, can you please confirm the device ID for nRF51822 QFAA G1?
The HWID I discovered is 0x004A
Pls confirm so I can pull an update request for Black Magic Probe...
I tried to run the ble_app_hrs_freertos example on the pca10040 devkit, but it's not possible to connect via ble (using nrf connect, neither with pc nor with smartphone)....
Hello,
I'm testing the capability of BT5 so I bought two nRF52840 Preview DK (I also have one nRF52832 DK) and I have some questions that may speed up the work.
...
Hello,
i am writing an application which uses the SDK13 peer manager library for bonding. The Nordic chip is acting as a peripheral.
Is there an easy way to prevent...
Hi，I update my IAR IDE from version 7.70.1 to 8.11.1，when I compile the workspace ble_app_hrs_freertos_pca10040, the error occur in port.c, as following:
Error[Og014]:...
First try to create a TWIM driver from scratch without any DMA. Following the steps in the OPS I get mixed behavior and only the chapter with DMA generates any clock and data...
I ran into an odd issue on nRF52840 using s140 version 5.0.0-3.alpha. My application erases and writes to a region of flash.
I've found that I'm able to erase the pages...
Hello,
I have implemented experimental DFU buttonless example with my application and able to do the firmware OTA via secure bootloader example using private and public...
Hi,
I'm experimenting with the nrf52840 preview board.
I have tried the example "ble_app_att_mtu_throughput" using the coded option to check the extended range and it...
hi, everyone!
I have a question for pstorage, when i use pstorage_store,it was failed, return error code :15 how to solve it. Below is my code
void custom_flash_init...
With good luck, I traced my connection timeout to the slave/peripheral using nrfSniffer. What is most unusual is the slave unexpectedly stops corresponding with the master...
