Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
sd_softdevice_disable before flash_page_erase and flash_word_write ,
after i want set sd_softdevice_enable ,but system is error
how can set sd_softdevice_enable after set...
Hello,
I'm using: nRF51422-QFAA E00 and SDK - nRF51 5.2.0
My problem with ADC is that I stucked when waiting for event - end of conversion.
I used the code from Nordic...
Hi everybody!
I've plugged my NRF51422 as a slave on a STM32 through a SPI bus. I would like to be able to send to the NRF an unknown amount of data. I also need to read...
Error happened in pstorage_init() when sd_flash_page_erase(), return value 0xF.
I use S120 examples. So I guess maybe my device don't support S120 ?
My device info:
nRF6310...
Hi
I'm new nrf devices,
I'm trying to flash my device via nrfgo studio but every time got error.
Here is screenshut of program:
Edit:
J-link commander connection...
Hello all.
We are novices and apologies for possibly the annoyingly trivial question.
We are starting in developing a new BLE peripheral with a custom GATT based service...
Hi
I use
sd_ble_gatts_value_get(p_beacon->beacon_char0_handles.value_handle,0, &len, gatts_valuebuf);
to get the value.
But even if I write two bytes, the len...
I want to get size of the project executable and display it in make file. How to get exact size of the executable file in make file.
Can you please provide the make file...
Looking at the documentation for SDK 6.0.0 this error doesn't seem to be a normal return from this function.
After searching the error code in to forum I read that this...
I'm using the S110 v7 SD, I want to amend the bootloader app such that I can merge it with my APP together with the SD to a single .HEX... To do so I'm taught to init. the...
Noticed that the WLCSP packages are being offered with a "build code D0". What does the D0 signify ? Any implications to programming the chip?
www.semiconductorstore.com...
I have tried to merge the hex files using mergehex, and flashed it to my device.
After flash the device is in DFU mode.
It seems the booloader doesn't know that there...
Could someone please explain or point me to rules for creation of such type for custom service?
I did look at provided examples but there are no comments telling why members...
I have a vendor specific characteristic for the battery voltage in my device, expressed as an actual voltage rather than a percentage. Values are 0.000V to about 4.300V and...
