I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi,
as I understand (and tried), in order to get low power consumption on the NRF91, I need to to get CONFIG_SERIAL=n.
However , I need the uart to be enabled (for short...
Hi - I am wondering what is the power optimal way to read/write with the TWI module. I do a tx and rx with the TWI interface. I have something like this, from the examples...
Hi,
We have just almost finished develop a product which used nrf52840 as a data hub, a wifi module connect to nrf52840 through uart, and baudrate set to 460800, and also...
Hi ,
I am using the example "ble_app_uart".
I enable uart while receiving data from nus handler and turn it off after transmitting.
After I mondified the code, it can...
When trying to write the bootloader hex file to the device with nRFgo Studio, the following error message is displayed.
[nrf52840_xxaa_s140.hex programming failed: This...
Hello
I'm using SDK 15.2 on nRF52 DK to test the ble_app_multirole_lesc example.
I downloaded the code to nRF52 DK to act as central.
I commented the scan_start() function...
I take bootloader_secure_ble example for pca10056 build it and use hex file to program using nRFGo Studio get error verification Failed. if i programmed with keil then load...
HI,
I'm having a problem when I use the function nrf_drv_twi_xfer. The function returns the error code NRF_SUCCESS, but using the event handler I notice that I'm receiving...
I am using nrf connect app on ios , the device is getitng on device mode but it is not showing DFU button on it , but it is working when using android app of it
And...
Dear all,
I am using SES, I have an application that relies on a softdevice. For it I developed a custom bootloader that DOES NOT rely on the softdevice and only transfers...
Hello, Nordic! I'm developing with a nRF52832, a bmi sensor and SES. I am starting with the BMI160 libraries on github and encountered some problems with the call of the i2c...
I am trying to implement a simple matrix 4X4 keypad. I have an issue in enabling gpiote events. I disable gpiote events when there is a row event and i scan the keys by turining...
Hello,
We were wondering under what conditions the SIM will reset. AT commands will give us activity on the SIM_CLK and and SIM_IO lines, we are looking to see activity...
Hii,
I have two question regarding advertising and connection
1. Is there any way to hide my peripherals advertising from any other central scanner .
2. Is it possible...
Hi
I did test two sample code with nrf52DK kit in segger embedded studio. with sdk ,nRF5_SDK_15.3.0_59ac345
1) ble_app_uart (I connect one sensor with UART,I did some...
