Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
hi -
so i did a little research and it looks like the java virtual machine for the ME edition will be able to work on the dongle. However i could not find any literature...
I am starting to debug nrf52840 UART example. I tried to change clock to internal RC oscillator then I am trying to connect nrt connect Mobile app, adverting happening but...
Dear,
I am using ncs_v1.0.0_rc4, and got the FW mfw-nrf9160-1.0.0-25-rc2.prealpha from . I want to update this FW
I tried to use nRF Connect v3.0.0 Programmer
/Cellular...
I am developing software for the nRF52. As recommended by many recent posts here in the Developer Zone, I have upgraded to SDK 11. I am working on an application for a battery...
Hi, I would like to share some valuable information regarding the BLE DFU (secure bootloader) and a MESH application which uses persistent storage for provisioning data. I...
Dear all,
I'm using two nRF52 Preview DK boards with the SoC nRF52832 and I'am testing the light switch example with sdk 3.1.0.
For my application I need one client...
MY CHIP is NRF52840, EVB is PCA10056
SDK: nRF5_SDK_15.0.0_a53641a
bootloader use secure DFU example: \nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_ble...
Hi,
I found your PDM Working Example. However I wonder what to make of the data I get.
What is the CONFIG_PDM_BUFFER_SIZE_SAMPLES for? Do I get 16Bit Bit-Schemes from...
I am using SDK12.3.0 + SoftDevice S130 in nRF51 DK.
I create 4 channel PWM (+ppi) in timer1 & timer2, because I know timer0 is used by Softdevice, RTC1 by App_timer.
My...
This is more of a Segger question than an Nordic question, but it seems enough folks here use J-Link tools that I could ask here.
RTT Logger and RTT Viewer doesn't log the...
Hi Nordic community
I want only send data using ble app_uart example with out receiving anything. So i tried to send the data that i received from my device to my android...
I am working on the safety-critical system, I have, ON and OFF function, the entire system using UART communication. In which I am using the nrf_queue() and push the data...
Hello everyone,
I have been using nRF52832 module from Raytac ( link ) for my circuit and I got a trouble with sending advertising packages to other master devices. I installed...
Hi,
I am trying to merge working code that places the microcontroller in system_off when a switch connected to pin 16 is opened. It then wakes up the micro controller when...
