I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
The project is cobbled together, but starts from TWIsensor in the SDK 14 examples. The project is compiled with the gcc toolchain which has not given me any trouble. The project...
I am trying to use UART with interrupts and fifo, by using nRF52 SDK 12.2.0 example. It works until the first overflow, after which I cannot any more receive characacters...
Hi!
I'm using an NRF52 with app_uart. As expected at 115200 baud rate, I occasionally get overflow errors which I can see in my event handler.
However, after these errors...
Hi,
Where are scan requests sent? I'm trying to find the function that does this because I would like to disable it.
I only want to connect with a peripheral based...
Hi everyone:
I am using the NUS (nordic UART service) in my project, and find one problem in this project. The development bench is: SDK13.0, nRF52 DK.
If I build a NUS...
Hi,
I used IOT TCP Server example of nRF5 SDK(Ver.15.0) to complete the communication
between the Raspberry Pi and the PCA10040.
But I found that the communication speed...
Hi,
1. I want to disable MCU UART connection which is SB with GPIO pin 5, 6, 7, 8 and I need to connect that pin on arm based processor so desoldering those short bridge...
Hello,
we are facing a weird issue with a few models of smartphone since we increased the max MTU size. We are testing at the office with the Xperia E6553 but the Samsung...
Hi there
I am stuck. My incremental wheel with photocell and comparator circuit does not work if the QDEC hangs on it. But seperately it works fine.
When I hang it to...
Hi Team,
Which models are supported in the latest mesh SDK?
I can see support for the on-off model.
Is Time and Scenes (Explained in Mesh Models.pdf, Section-5, Page...
I use SDK13, nRF52, S132
I use bootloader_secure_ble with generated public key for bootloader and for nrfutil. After all steps like discribed on
devzone.nordicsemi.com...
Hello.
I use nRF52832 and power from 3.3V source. Also I use the accelerometer and gyroscope with VDD 2.5V and 3.0V respectively. They are connected to nRF through SPI....
Can a device that is configured and programmed from Keil (softdevice, application, bootloader) be updated with code that has been compiled on ses (application)? I have converted...
Hi,
Referring to bootloader programming article - there's a post-build phase of programming UICR.BOOTLOADERADDR
The article describe how to use nrfjprog to do this which...
