Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi engineers, I got a question regarding nRF52840 (PCA10056), i want to run DTM using PCA10056 board with MT8852B tester. Unfortunately, i keep failing to get the EUT address...
Dear all,
Our application is made of
Chip nRF518122 + SDK 11.0.0 + DFU Bootloader + BLE application (gcc complied) loaded with nRF Toolbox over the air
we are putting...
Hello,
the nRF9160 product specification 1.0 states in 5.1.4.2:
"Note: The LTE modem requires using LFXO as the LFCLK source."
I checked the clock register and noticed...
Hi,
I have developed an SWD working code which read-write the Flash Memory and RAM which is working very good.
Now I have a problem in I need to write start address...
Due to time pressure, I'm starting this thread based on an existing ticket: https://devzone.nordicsemi.com/f/nordic-q-a/51423/firmware-on-custom-board-application-bootloader...
Hi team,
We have a customer who has some questions about GPS.
The questions are:
Where do we save the Ephemeris data when GPS code start? RAM or flash?
When use...
Hi,
Can an nRF5x device be configured as a BLE relay with Bluetooth Mesh?
I believe with the Central-Peripheral-Relay example, the Relay needs to establish connection...
Hi. I am trying to create a dfu zip file that contains the softdevice, bootloader, and application. I am DFU upgrading an NRF52 device from SDK v13 to SDK v14 via Nordic's...
Hello,
we are using the nRF52840-DK.
File: secure_bootloader_ble_s140_pca10056.emProject
File: ble_app_buttonless_dfu_pca10056_s140.emProject
In short, we are...
Hi,
I have a well working cli environment under linux where i can compile, program and debug a nFR52 demo board.
I have installed RSSI Viewer (1.05) and Bluetooth Low...
We want to deactivate Mesh DFU packets relaying from the App side to avoid messing with the bootloader firmware. Is there any flag we may use for that?
Hi,
I'm trying to use a Bulk IN endpoint (EPIN3) and am running into an issue.
I call the nrf_drv_usbd_ep_is_busy() function to test whether it is safe to proceed with...
Hello
I am using buttons less DFU,
S132_nrf52_6.1.1 softtdevice
using Android + nrf connecct, I can update the device with DFU
using IPhone 6, I can not update...
I am able to provision using BlueZ's meshctl tool on Raspberry Pi3. However, after restarting meshctl, I am not able to control my device. I tried the "connect" command after...
