Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
Hi,
I can't seem to find an example for receiving an update about restored value of CCCD when a bonded peer reconnects. I'm using SDK14.
NUS and HRS examples which use...
I am new to Nordic, and Keil, and not especially strong in microprocessors yet. I am trying to get currently developed firmware for a nRF52382 chip to operate on a custom...
hi expert
i use sdk14.1 ,nrf58312, when my phone(andriod 5.2.1)connected to nrf58312 board ,i find the addr type is 2, so i want write the mac to whitelist ,but when i set...
Hi, I wondered if the source code of the SDK 51422 PCA10028's firmware is available ? The one firmware which allows the SDK to flash other nRF51X over the air? If it is, where...
While the default microphone mode on the Thingy52 is ADPCM - which I got working fine in my evaluation environment - the SPL mode defined in https://nordicsemiconductor.github...
Hi,
I am beginner for nRF52840. I use Keil uVision 5.20 to develop firmware. I have a problem with the Nordic packs downloaded from Keil website. The USB driver is not take...
Hello.
Until now, we work with NRF52832 for a new product but we have identified that the memory (64kB of RAM and 512kB of flash) of the chip will not sufficient for our...
Maximum connection node in 6lowpan over BLE
I am testing Pi to Nordic node (NRF52832 IoT Softdevice). When I test connection, maximum connection node is 10. Do you know...
Dear all,
Sorry for asking an old question but I can't find any similar situation in the forum. I now have 3 boards: 1 is 52810 EVB, 1 is 52810 QFAA ( 48 pins) custom made...
I bougth pca10056 and I need use it with Keil, but I do not find the pack installer for this board on "Pack Installer".
Furthermore, keil does not recognize my board.
...
I am using a lithium polymer 4.2V battery to power an nRF51822 (as a side note the power goes through a voltage regulator before going to Vdd). I want to be able to check...
When calling app_sched_event_put() no check is done whether the exact same record (same data, length and function pointer) already exists in the queue. We have setup where...
Hello,
I've tried to implement a custom service with a custom chacteristic, that shows the values per notification in the MCP (Master Control Panel) in percentage.
I played...
Hi,
I am using NRF24L01 module and I would like to transmit I2S signal through this module. I used SGTL 5000 audio shield for converting audio signal from microphone to...
Hi,
I'd like to determine the cause of a watchdog reset. I was hoping to utilize the WDT event handler (passed in to nrf_drv_wdt_init() ) to record the PC of the application...
