Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hello,
I am running a simple application where I would like to listen for BLE packets for 100ms and then transmit a packet. (no soft device) I can successfully capture...
In section 17.1.9 of the nRF51 reference manual it states:
Maximum consecutive transmission time
is defined as the longest time the
RADIO can be active transmitting...
I need to connect VL53Xl to NRF51 DK> I am using latest 12.2 SDK with Keil MDK.I cannot find any I2C(TWI) example. I can find examples for NRF52 based devices. but not for...
I am using a nRF52832 which act as an observer role only and what is observe it send observed data to another device over UART.
When i turn off scanning and just run UART...
Hi,
I generally use " make flash" (armgcc makefile). If there are multiple devices connected I get a pop-up to select a device/emulator to be flashed. This pop-up just defeats...
Hi there,
I'm trying to use nrfutil generate package with an extern key pair generated with openSSL.
I used opneSLL with prime256v1 curve, which correspond to secp256r1...
Hi,
I use nrf51822 with HF XTAL Frequency of 32 MHz
I am migrating from SDK9 S110 to SDK 12.2 S130 and have a problem that the code stop on nrf_delay_us.
#ifndef...
we wrote a small application to jump to a desired address of our application from bootloader , but UART does not seem to work(i cannot see any transmitted values on terminal...
Hi,
I would like to use the ble_app_hrs to send pressure values via the heart_rate_measurement_send function.
Unfortunately, they are too long: around 105000 Pa (equals...
Hi everyone!
I have an application based on experimental_ble_app_eddystone for nRF52 (SDK12.2), which uses FDS to save in flash memory. Now I want to add the secure_bootloader...
Hello on git hub you add pc-ble-driver
but there is only help how to install it. I did not find any example. And I did not find any documentation how to use it or what is...
Preface: I am developing a software working with different radio protocols (enhanced shockburst, bluetooth,...). Therefore I implemented uart commands for switching radio...
Recently i have purchased nrf51822 and nrf51dk but i dont know how to flash softdevice in nrf51822 using nrf51dk.
please expain me how can i flash or where can i know how...
Hello,
I have a problem running nRF51822DK with temp. sensors while running BLE. I tried DS18B20 but it doesn't work at all, then TMP36 with ADC reading and as it works ...
