I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Hi,
i have only little experience in programming a nRF51, but i want to make just a simple application.
before i used a btm222 BT2.1 SPP module to transmit serial UART-data...
Dear Nordic Support Team,
I am trying to write some information in the flash memory without success. In the ble_flash.h file, it is specified that the pages 0-127 are reserved...
hiii....
1.can any one tell where do we call advertising_start() function if we want to advertise after getting disconnect from a central device.
2.in ble_evt_dispatch...
I`m a newbie at Bluetooth Low Energy and Nordic Chips. I bought a DK for the nRF51822. I would like to set I/O pins over android and iOS application.
1.So what application...
Are there any common solutions to the issue of spi_slave.c using an array as its buffer? I would like to setup a circular FIFO, but I am not sure if there is any way to do...
We are using the S110 as a peripheral that emits data via notifications.
Is it safe for the central to also send characteristic writes while notifications are being emitted...
First of all ,i download the SD7.0 to my device, then i download my app to my device,in this case
my device's curent is 100uA.
First of all ,i download the SD7.0 to my device...
Hello,
i need some informatiorn about the layout of the nRFgo Motherboard. More specific i want to build a board which is connected to the ports P0, P1, P2; therefore i...
I'm trying to implement a burst transfer between to nRF24AP2 devices, but I have serious problems getting it to work.
The burst messages are send on a reverse channel to...
Hi, I need to read an analog signal 100 s/s which takes 68us at 10bit. There is very little computation to be done once read probably about 10us which I can do to the previous...
I am experimenting with calling sd_flash_write with waiting,
if it returns NRF_ERROR_BUSY, just try again, and then return either success fail
void flashWrite( uint8_t...
Hey ho,
I'm new to BLE and Nordic. I'm a student from Germany and i want to realize one simple function with Arduino (RedBear Blend with nRF8001) and Android.
I want my...
Hello,
We've heard that the BLE transmission packet length may be increased beyond the limit of 20 bytes in a future version of the S110 softdevice. Would you let us know...
Hi
I struggle to understand mechanisms of switching particular subsystem of nrf51822 off and on again in order to consume as little as possible current when MCU is put...
