Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
I am using nrf52832 sdk14.2.0 to develop now, I want to realize the following function on the basis of PWM_driver example, output the following waveform on P0.22: 1ms high...
Hi all,
I am newbie with nordic, and I need some help.
I am using nRF52832 with softdevice.
I need to generate a 128 kHz clock signal (PWM pulses with 128kHz frequency...
Hello,
I'm doing some power evaluation of the three PHYs of BT5 using the PCA10056 preview (v0.9.0) and the PPK (rev 1.1.0), moreover I'm using the ble_app_att_mtu_throughput...
I've seen variations on this question, but never quite been able to decipher a complete answer:
I've built an app for the NRF52DK based on the nRF5_SDK_15.0.0 "Hello World...
i created a mesh network using light_demo in NRF52832SDK and i need to scan a new device to make it join my mesh network .when there are a number of devices and i have to...
Hi,
I am working on the port of the nrfutil library of python -> C and I am looking for a support to understand the python code of the nrfutil library please.
Can you...
Hi
I was designing nrf52832 based PCB and using Jhonson's 2.4ghz antenna. The PCB is 2 layer and I am following the guidelines of chip antenna as given in the datasheet...
Hello:
We had a main application with NRF_LOG using RTT as its backend, and it was working great. We are using the BLE_DFU and recently added NRF_LOG capabilities to this...
Running through the ble uart example, connecting to the nRF connect app on my android phone. If I'm not actively sending data the bluetooth connection will time out on the...
Hi team, I am using nrf52 sdk 14, nrfjprog version: 9.7.3 and JLinkARM.dll version: 6.14c,getting this issue while flashing:
ERROR: JLinkARM DLL reported an error. Try again...
Hi all,
I have a functional FW, which is running properly 99 % of the time. But sometimes I have some RESET with RESETREAS register set to SREQ, but I'm not able to find...
Hello,
I am completely new to creating a Bluetooth mesh network and nRF5 devices. I have three nRF51 DK and 2 nRF51 dongles. I have earlier read the posts and made nRF51...
I am working in sdk15 nrf52832 ble_app_hids_keyboard.
I want merge ble_app_uart_c ,so modify in
sdk_config.h :
NRF_SDH_BLE_CENTRAL_LINK_COUNT 1
PM_CENTRAL_ENABLED...
Please check the Device above its nRF52832 based device.
I want to program Softdevice and app using nrfjprog from my PC // or by using nRFStudio
is it possible ?
