Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
Hello,
I would like to use the serial port library with free RTOS. I read several threads that timeouts do not work when using free RTOS. So I tried to use the lib without...
Hi There,
I want to pair my nRF52840 BLE module with a laptop over the bluetooth, while, I cant able to connect it. Now il will explain the whole scenario.
I have downloaded...
I'm running Windows 10 and loaded pc-nrfconnect-ble-231-master from GitHub,
Per the README I npm installed windows-build-tools, then npm install.
I got some warnings about...
I am using nrf52832 dev board . I have used the example code of ble_app_beacon code . I am able to send my data through the beacon. But while using nrfconnect app, the scanning...
HI,
I've been using the Nordic Command Line Tools to do the following:
program an example hex file to the SoC
read the code, ram, and uicr registers and save to file...
Hello.
My question concerns UUID.
Exactly where does it come from?
Can I generate this UUID for my own application ( https://www.uuidgenerator.net/ ) or maybe it is...
Working on a migrating RF test firmware that was working on 52832 using SPI to AT86RF233(for 802.15.4). Was able to exercise PHY with that setup to send specific packet with...
Hello, Nordic!
I am wondering about PCB reference design for AoA multi antenna locator based on 52811.
Could you provide it before releasing software supporting this functionality...
Hi. I looked through all the examples in the 15.20 and 15.30 SDK and could not find even one project for SES with it's new linker as an example. all the examples use the old...
To be able to SMS we need the SMSC number stored in the SIM card.
I did not find an AT command to read this, so I gues we need to use the +CSIM or +CRSM?
Regards,
F...
I am using nrf52832 for button less DFU. DFU is working fine when CONFIG_NFCT_PINS_AS_GPIOS is not added in applicaton. When added seems like code is getting reset at bootloader...
I have problems compiling code with modem info support on. My basic problem, I want to establish which modem FW version I am running on.
I added
MODEM_INFO_CONFIG=y
...
We successfully built the mesh bootloader, but want to get RTT working with the bootloader logs inside SEGGER.
We were following this two posts post1 post2 to achieve our...
Hello guys.
I just donwload new version of SDK 1.0.0 for NRF9160 and try run mqtt_simple demo. I didnt change nothing there and there is problem.
I have the follow log...
Hello,
Currently my beaconing application draws approximately 10uA @ 1000ms advertising interval. I am having trouble getting the chip into system power off mode so the...
