I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi, I was using eclipse for the development of our board using the nRF52832 and when I launch the debug on eclipse, the program does not flash and this is the output that...
When using "nrfutil dfu serial" can it be configured to log all the bytes transmitted and all bytes received in a log file or on the console?
A colleague of mine is starting...
We have found what appears an easily reproducible bug in nrf_serial_read.
Reproduce as follows:
* PCA10040
* SDK 15.3
* SES
* Example project peripheral serial ...
Hi everyone,
I'm working on the nrf52832 using the SDK 15.2.0 with freertos and the application I am developing requires to save data on the flash while the BLE stack is...
Hi
When a GATT Table is created using the softdevice api, how do specify that a service or characteristic shall have a minimum key size of X so that if the current encrytion...
I am currently developing an app on Android studio that should detect nrfDongle.
I successfully uploaded UART software from SDK 13.0.0 to dongle and it is being successfully...
Hello, i want to know is it possible scan iBeacons with a node using nrf mesh with proxy features like the light switch node server example? if this is, how i could start...
Hello.
I have pa/lna on my device. It works properly in application (rssi is about 30 dbm). But when application goes into bootloader (dfu over ble using nrfconnect on android...
Hi, I'm using the nrf connect mobile app and I want to connect multiple devices to the advertising device and I want them all to access the same characteristic at the same...
When I open SES it says that it cannot detect any j-link so it asks me to buy license. But shouldn't my nrf52840 dk board have on-board j-link that SES should detect? I check...
Hi,
as I understand (and tried), in order to get low power consumption on the NRF91, I need to to get CONFIG_SERIAL=n.
However , I need the uart to be enabled (for short...
Hi - I am wondering what is the power optimal way to read/write with the TWI module. I do a tx and rx with the TWI interface. I have something like this, from the examples...
Hi,
We have just almost finished develop a product which used nrf52840 as a data hub, a wifi module connect to nrf52840 through uart, and baudrate set to 460800, and also...
Hi ,
I am using the example "ble_app_uart".
I enable uart while receiving data from nus handler and turn it off after transmitting.
After I mondified the code, it can...
