I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi,
I am working on NRF52 custom board with 3.7mA 27mAH battery, working on BLE app UART example SDK11 with SoftdeviceS132V2.0.
I made BLE advertise for 20 sec interval...
I prototyped a nRF52832, WLCSP package, with a fab (PCBA) and put jumpers between my 32Mhz crystal and the chip, attempting to connect with a j-link in SWA mode, I cannot...
Hi. I'm using nrf52832.
Now I'm using HFXO, LFXO to operate BLE. As I know I should use HFXO to operate BLE.
What about LFXO? Can I use internal clock(LFRC RC osc) instead...
Hi,
I am working on the latest version of SDK (v14) and SoftDevice(v5) on nRF52382. When I call the sd_gap_disconnect it returns NRF_SUCCESS. However the BLE_GAP_DISCONNECT...
I was trying to verify the DFU functionality on SDK 14 on nRF52832. Here is what I did.
1. Using nRFgo to erase all
2. Program bootloader/soft device with C:\svn\nordic...
Hi,
I am using SDK v12.2 and gcc compiler. S132 softdevice for nrf51822 controller.
And i am using s132 softdevice.
I want to connect multiple nrf51 devices (approx. 14...
Hello sir,
I am using nRF52832 board and interface with 3 axis accelerator reading ADC for 3 Channel. I have use sample code for controlling in timer/RTC mode. My ADC is...
Hi,
I'm doing some measurement on the radio peripheral of the nRF52840 using the generated events and a timer which is set to run at 16MHz. Radio events and Start/Capture...
SDK version: 13.1
Hardware: nRF52832
Eclipse version: link text (I could not get the marketplace working in the latest Mars Eclipse version, so I downloaded this version...
I am evaluating the sdk14 ble_app_uart example. I am able to run this code and connect to this uart service but do not see messages get passed to the uart pin. Only when I...
I am using a nrf52832 Development Board with s132 for some BLE applications. I developed a beacon app, set for BLE peripheral, and every reading of the advertising from this...
Hi,
I'm using NRF51 DK board and i am following characteristic tutorial available. I am able to send temperature value over Bluetooth by using light blue app.. Instead of...
I am using nRF connect to debug an application on a nRF52832. When I perform a scan, I can see the UUID of the nRF52832 device I want to connect to. Where is this UUID stored...
Hi,
I'm unable to auto connect with nrf51 using nrf Connect App, if I select Connect using Auto-connect only and no Bonding in nrf Connect App for first time.
With Auto...
