Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am using jlink to program the custom board. I was able to program the board earlier, but now this error is comming. I have rechecked the connection and it is fine.
The...
Hello all,
I am in the design stage of custom board for Automotive application using nrf51824. i have the below queries,
In the below link there are two reference...
If the DCDC is enabled in the nRF52832 and during operation one or both the external inductors is damaged what is the effect on the device? Will the power sub-system compensate...
Hi,
I can send and receive commands from nRF51 Dongle to nRF51822 via using nRF Connect UART over BLE Service.
My question is : Is there another way to reach nRF51 Dongle...
Hello,
I have chip nrf51822 connected to nrf51dk. An usb connection provides power to both chips. While checking power of both chips via nrf connect on iphone7 i discovered...
Connect establish with smartfone in peripherial mode. SDK13. S132. Periodic I observe disconnect, than 2-3 advertise packet and new connect again.
Where can I see what reason...
I have a little hobby project going on where I'm trying to make Nordic's old temperature broadcaster example work with the nRF52: github.com/.../
The project was originally...
As the product specification says,The HFCLK clock controller provides mang kinds clock to the system:
HCLK64M:64MHZ CPU clock
PCLK1M:1MHZ peripheral clock
PCLK16M:16MHZ...
Hello Folks,
I am currently try to program RedBear BLE nano board (which is essentially nrf51822) using Nordic SDK v12, which has features of secure OTA. However after...
I have started working on the external file access with NRF
is it possible to read or access the data from the external file into NRF programming
similar to what we do...
I am running a modified version of the app_uart_c example on a nRF52832 using softdevice 132.
I want to send a large hex number to the peripheral I'm connected to. Is it...
Hi,
No matter what I adjust, I can't get the PPK to output over 2.2V. I happen to be using an older nRF52 preview DK (figured it'd be a good use for that board now that it...
tl;dr: UART transmission sometimes stops and never resumes. Only a
power cycle resolves the issue; a system reset is not sufficient. The
problem only occurs when flow control...
Hello,
as far as I have gathered, it is possible to use multiple peripherals on one device with the current alpha release of the S132 Softdevice. What I did not understand...
