I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I have the nRF51822-DK and have been able to build and run the sample projects, e.g, ble_app_beacon.
I've just built a board using Taiyo Yuden's EYSFCNZXX module that's...
test the gpiote_example for timer0 in pca10003, the function is ok, LED blinking 200ms. but I change the timer0 to timer1 or timer2, the LED always on,and never blinking....
Hi! I use S130 on nRF51822 device.
After device is connected as peripheral I try to discover services using Master Control Panel but device disconnects. In Master Control...
I'm trying to start advertisement after establishing peripheral connection (on BLE_GAP_EVT_CONNECTED event) but called function sd_ble_gap_adv_start(...) returns NRF_ERROR_INVALID_STATE...
Hi
I'm working on a project to drive a DC motor, I really didn't find any example. I would like to know how can I program a pin in Keil, and I would be happy to have a...
Hello,
I am trying to get a lower connection interval from iOS. But the lowest connection interval I could get were 30ms.
Anyone has experience to achieve the connection...
Hi.
I find this code github.com/.../nrf51-dfu-single-bank-ble
I want to compile bootloader and download it on PCA10004.
I have KEIL 5.12 and the project file of the link...
Hi,
I want to create a service for test logger. Through this service i want to write n bytes at a time and after few delay want to write again some n bytes. These written...
I'm struggling to get started using Keil with an NRF51822 mounted on a custom board that I have cobbled together.
I have opened the blinky/pca10031 example as a starting...
Hello, I have two nRF24L01 devices that can already talk to each other on a custom address. When I try to talk to the nRF51822 from one of the nRF24L01 devices, I cannot get...
services.h
Hi,
I'm writing an interface for my nRF8001 and am a bit confused about the NB_SETUP_MESSAGES value. In my services.h file the value is 14 when it appears there...
May be i haven't seen it, but how i can select if the setup will be stored in the NVM or volatile storage.
I prefere to start development with volatile storage.
On Page...
Dear All,
I used the array defined in services_lock.h to setup the nrf8001 module. Therefore, the service setup is written to the OTP memory in the chip. Now, I want to change...
