Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi all,
I'm hoping someone can explain a behavior I've observed. I have a workaround but I want to understand the mechanism.
Setup
nRF54L15, NCS v3.1.0
ICM-42670...
NCS 3.1.0 (and newer), nRF9160/51
Some applications using "at_host", maybe together with "at_cmd_custom", would benefit from a possible filter before passing the at-cmds...
Hi,
I'm trying to install the nordic sdk/toolchain combo via nrfutil command line (Windows x64) and I get the following error:
Is there any known way to resolve this...
HI,
I am developing an NFC application using the nRF54L15 with SDK version 3.2.1, and I am using NDEF for data exchange. However, I have encountered an issue: after the...
Dear Nordic Team,
I hope this email finds you well.
We are reaching out to seek your guidance regarding an issue we’ve encountered while testing Matter firmware updates...
Hey all,
I've been working on a family of commercially available cellular IoT devices using the LwM2M protocol utilizing nRF9160 and nRF9151 SoCs. In the European Union...
Was excited to get an (apparently) early copy of the nRF54LM20B-DK so that I could explore all the Edge AI capabilities of the system (using both Neuton and Axon models)....
I am testing the NRF9151-SMA-DK NTN function using the mfw_nrf9151-ntn_1.0.0 firmware and serial_modem_v2.0.0-preview1_nrf9151dk_normal_mtrace app. I keep seeing
%MDMEV...
HI,
I'm reading this post about NFC antenna matching. It says in Method 1 to connect the coil antenna to the S11 port of the network analyzer. How should I make the connection...
I am currently working on a design with the nRF9160, and have a few questions about the DEC0 pin and decoupling for the module in general. I have been considering adding additional...
I keep seeing this in your documentation:
This functionality is in the process of being deprecated and replaced by Zephyr’s default devicetree-based memory partitioning...
Hi,
I am testing the radio_test (short-range) sample on an nRF54LM20A DK . The test setup is:
Board: nRF54LM20A DK
Sample: peripheral/radio_test (NCS version...
Hello Nordic Team,
I am evaluating the nRF54LM20B physical DK using nRF Connect SDK v3.3.0‑preview2 . In the SDK, only the nrf54lm20apdk board target is available, and BLE...
Hello, I am working with the following sample project and NRF Connect SDK v3.3.0. (Referenced regarding this topic .) The sample implements DFU with MCUBoot while using the...
