I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I've been trying to integrate CLI over USB CDC ACM into my project, but I'm failing even to run the SDK example.
CLI works fine over UART, but it won't run over USB.
...
Hi,
My application has hard faults sometimes, and I'm trying to figure out the reason.
When it occurs - I have a hard fault log, but p_stack->pc is 0. I can't understand...
When I use j-link soft uart all good
but when i disconnect j-link the soft uart will error
like this so�rceid=2, status=0 sourceid=3, status=0 sourceid=4, status=0
Hello,
I'm new to BLE product and nRF52840 dongle and DK are my first BLE evaluation kits. I've some experience in Arduino AVR microcontroller. My setup is as follow:
...
Hi All,
I've been successfully using Martin's example - https://github.com/Martinsbl/nrf5-mpu-examples/tree/master/nrf52-mpu-easydma-using-gpiote-and-registers - for DMA...
I need to connect a PN532 V3 Module to a nRF52840 using SPI. I tested it using arduino IDE (I used those three libraries: Adafruit_PN532.h ( github.com/.../Adafruit_PN532...
We have custom board which is interfaced with PCA10040 board through bebug out port. Blinky example is working fine on 10040 but when I download it on evaluation board its...
Hi,
I've been following below tutorial and everything works fine.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-characteristics...
The loader script provided to Segger for use with Embedded Studio includes
. = ASSERT (( __tdata_load_end__ <= __storage_flash_start__),
error: section .tdata overlaps...
Hi, I'm working on a project with the nRF52840 PCA10056 board. Using the IoT LwIP MQTT example, I can communicate with the insecure MQTT. However, I need to provide security...
I would like to use the GATT queue to discover ALL primary services. When using the SoftDevice calls directly, one would use sd_ble_gattc_primary_services_discover(conn_hdl...
Hello
I'm going to use AES for encryption and decryption testing of data this time.
Looking at the example of SDK, there are several AES modes, can you tell me the difference...
Hi,
I'm a beginer with Nordic Semi tools, I use windows 10 on a laptop HP-15DW1023NF.
I received last week a nrf5340DK (PCA10095 0.11.0 2020.51 960132679) and I installed...
