Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello,
I'm having issues getting my SPI to work at high transfer speeds. I have my pins configured to have high drive.
SPI is set to MSB first, Mode 0.
Colors:
Brown...
Hi All,
I am using SDK17 for my application currently. To sense ping change I am using app_button function as below. Normally my port pin remains high and current consumption...
Hi,
I am working with a NRF52840 with the SDK16 and I am facing field issues with the peer manager flash usage. At each connection the app subscribes to characteristic and...
Hi,
I wonder there is not any TX_POWER_LEVEL macro used/defined in the source code of below peripheral application.
"examples\ble_peripheral\ble_app_hrs"
Does it...
Hello, sorry to bother once more.
I am new to the nRF world and bluetooth in general, I am trying to build a device /app that gets data from 3 sensors. 2 of which operate...
Hi all,
in order to put the whole project under a decent version control system I need a list of all files used in the example project in segger studio.
The c source files...
Hello! I have the following issue with my nRF52833 board: I am in the first stage of working with it and I wanted to try the simple blinky example.
However, since there...
Hello,
I'm beginner with Nordic nRF52 devices.
I'm working on a PCA10040 (2.1.0) dev kit and I would like to communicate through TWI interface.
Then I have installed...
Hi! I was defining NRFX_WDT_ENABLED in sdk_config.h, but found that apply_old_config.h was undefining it.
Even though I had WDT_ENABLED defined to zero, the test in apply_old_config...
Please, give me an advice. I need to measure the supply voltage and trigger an interrupt after the measurement. An END interrupt is triggered only once. It must be without...
What's the difference nrf_cloud_agps and AGPS using google SUPL data?
I'm not clear about this. README.rst doesn't explain about it.
Also, to use the nrf_cloud_agps, do...
Hi Devs,
I am facing a weird behavior with my application, where the TWI writes return NRF_ERROR_DRV_TWI_ERR_DNACK or NRF BUSY
If I ran the TWI writes from the main...
Hi Nordic,
Does SLM application support IPV6, if yes could you please point us to the AT command set which configures IPV6 and also point to us complete AT commands list...
hi ... we have done one customized board which has nRF52832 controller interfaced with WINC1500 wifi via spi communication inbuilt. I have worked with the nRF52 example program...
