Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Dear support team,
I wanted to program and debug nrf52840 dongle through an external debugger. For that, I connected the debug out of nrf52840 development kit to the SWD...
Hi, I recently added the buttonless DFU bootloader on my device with the debug config. I am using and I can flash an application when in DFU. Although, I cannot debug my application...
Using the Mesh SDK 3.1.0 the advertising bearer's transmission interval is limited 20msec (B EARER_ADV_INT_MIN_MS).
The Mesh Profile Spec indicates in s4.2.19 that the transmission...
Is it possible to transfer 258 bytes over the TWI interface of the nRF52832 in one transaction ? The manual says that RXD.MAXCNT is 8 bit wide only. I need to read 258 bytes...
Hello,
I need help with my project. I am adding fds library to the light sw example.
I did this steps:
1. Included necessary *.h files
2. Added fds.c to the project...
Hi, I'm using nRF52840,
I created my app, then i tryed to program with bootloader using nrfutil.
I used dfu bootloader and i created a zip.
So i could flash bootloader...
Hi, every developers,
I am testing the example of ble_app_hrs_c and ble_app_hrs using 2 nRF52840 (in SDK 15.3.0 VERSION).
My goal is that data communication with two DK...
SDK : Mesh 2.1.1
IDE : SES
I have a node.
After this node provisioned the mesh network,I change this node model publish address by local.
then I restart this node...
On the UART and I2C operations, are the input/output pins configured using CMOS or TTL logic levels? I am trying to design a test to test signal integrity and there are some...
Hello, I am a new bee in using nRF52840. I have looked into the given example in SDK called usbd_hid_composite ( infocenter.nordicsemi.com/index.jsp . It worked well in my...
Hello everyone,
I need ble_app_beacon 1 second advertising and 5 second deep sleep mode i don't know how to implement that please suggest example code for beacon.
DK:...
I need to use Static OOB method with PyACI and serial library
When I sent cmd.OobUse with OOBMethod.STATIC , I receive error message: 2019-07-25 17:08:26,191 - ERROR - COM11...
Hi, I am planning to buy nRF52810.
I saw that nRF52810 has 24kB RAM and I think it should been more cause of my information of RAM.
But I am not so knowledgeable about...
Hi, I'm now trying to combine the i2C(Gyroscope) and Gatt service using nrf52840 (sdk15.3), but I can't understand how to add the service to my device,like service name:Gyroscope...
