Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using the reliable message communication to measure Round-trip time based on the Light switch example.
I noticed that in high traffics, some packets are not...
I want to use TimeSlot API for nrf52832.
two question.
I want to use time slots regularly . I call follow, timeslot_open() timeslot_request() - timeslot_end() -> IDLE_STATE...
Hi there,
I've already asked about it https://devzone.nordicsemi.com/f/nordic-q-a/49701/commissioner-disable and I've tried it but nothing work. I've already spent 5 days...
I am in pre production with the nRF52840. My customers have access to the micro USB port on the device. I want them to be able to define a string for the nRF5 transmitted...
I am using nRF51, SD 130 1.0 and SDK 10.0.0. I have 11 buttons connected to nRF. Currently it only works for up to 4 buttons (APP_TIMER_OP_QUEUE_SIZE is 4, but I'm not sure...
Hi,
i am working on spi master example in nrf52832, when clock is set to 8MHz, clk signal output at the nrf52 pin is more like triangle wave.
is there any way to set pin...
Hi,
At the moment, my current location does not have an NB-IoT network for the nRF9160 DK to attach to. This means that the device is unable to activate PSM mode (which...
Working with SDK 15 on an nRF52832:
I have a peripheral applicatin where I'm computing the value of a BLE read on the fly.
Currently I do that by:
Setting up a BLE...
Dear dev community,
I've got a very simple question: How can I see the subscription and publishing addresses list in any mesh node for any model?
Thank you!
Regards...
Hi I am developing a custom PCB for the nrf51822 chip. I heard the nrf51822 chips do not come with preloaded firmware or bootloader. Do I need to also flash the bootloader...
Base on nRF5_SDK_15.3.0_59ac345 for NRF52810, I wrote the following codes,
Use nrf_drv_uart_tx to send data is successful, and NRF_DRV_UART_EVT_TX_DONE occur normally...
Hi All,
I am interested in designing my own Bluetooth beacon (Several of them, about 10) and connect it to a computer and read sensor data from those beacons (For example...
Dear Nordic:
Hi,i install nRF Studio <nrfgostudio_win-64_1.21.2_installer.msi>, and i want to erase NRF52840 flash,but when i click on "nRF5x_Programming",i cannot get...
Hi guys! I feel really excited about working with Nordic Semiconductors, but I have a problem with PWM driver.
Do you know how to support 13 independent devices that will...
Hello,
I was looking into the nRF5280 and was going to purchase it. But I had some questions that were not cleared up in the data sheets. It seems that a battery or a power...
