Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I am using nrf_serial in IRQ mode to communicate with an AT based device. When I reset the device using ATZ, I get NRF_SERIAL_EVENT_DRV_ERR -- likely because the pins go into...
Dear All ,
I am finally able to get my beacon app to compile and work on the nrf51822 using keil with s130 softdevice.
I tried to add service data to the advertising...
Hi,
I have a situation where I have to create 4 TWIS instances on nRF52832.
sdk_config.h only shows 2 TWIS instances.
Is it ok if I add other instances (TWIS2_ENABLED...
Hello,
I was testing output on a GPIO pin with the mesh/dimming_server example and was only able to see 1.6V when measured.
I read through the example on infocenter...
Dear All,
I thought i wrote this question but seems it did not get registered. We are using the Beacon App from sdk 12.3 with the nrf51822 chip on custom board. I have...
Hello, I'm still a beginner with mesh so excuse me, if this might be a silly question or has been answered before. I did not find a post that quite resembled my problem. ...
I'm trying to use some code from the sample files and given libraries to create my own custom program. Upon startup, this is what I get:
Here is the only function called...
I am Currently under process of evaluating various modules for implementing BLE Mesh, Had few concerns regarding the same, would be great if someone can clarify upon them...
Hello,
I have seen today that the new releases of the v1.0.0 SDK and v1.0.0 modem firmware were release for the nRF9160 DK. I have been able to update the modem firmware...
Hi,
I am trying to migrate my project developed on Mesh SDK V2.0.1 to V3.1.0. I followed all the steps you recommend but i am stuck with the configuration of my server node...
hi all ,
i run Serialization application between nRF52840-DK ,it not start up.
how to Debugging this issue? i have been reset connectivity board,the error message halt...
I am trying to connect the MS5611 ( https://www.te.com/usa-en/product-CAT-BLPS0036.html ) using the GY-63 Sensor Module to the n RF52840 with the nRF5_SDK_15.3.0_59ac345 SDK...
Hello.
I would like to know which PCB surface finish would be used for bluetooth application. There are HASL, OSP and ENIG. nRF51822 IC chip and PCB trace antenna will...
Hello All,
We are designing a Tracking device system, for this we use nRF9160 LTE+GPS combo module. this system is battery operated so we need to monitor the battery continuously...
Hi,
I've been trying to lower the power consumption of the MQTT example and followed the guide in here .
1. I compiled the low power UDP example and do exactly all the...
