Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
We have successfully implemented & tested the working of SYSTEM ON SLEEP MODE feature in our nrf52840 devices.
Please reply to below queries for a similar issue:
Will...
hi, i've been trying to use uart in non-blocking mode (events available). Configuretion is the following: i have specify RX buffer (128 bytes) in init function, and in order...
Hi,
I would like to run the radio_test example on an nRF52811 chip for certification purposes.
What changes are required on the latest sample code and project to get it...
Hi all,
Is there any example to discover the custom UUID services with pc-ble-driver c/c++? As far as I understood, the ble_db_discovery is not supported for this driver...
Hi,
i am trying to Set TX power level from application using radio_modulated_tx_carrier() function from radio tool code. But when trying to run the code, application is...
Hello,
I am attempting to set up NVS to capture GPS data received from the modem for transmission to NB-IoT after collection has ended.
I have successfully implimented...
Hi everyone,
I m trying to communicate nRF52832 to an android application " nRF52 UART 2.0" on 9.0.
"nRF52 UART 2.0" app source is from git( https://github.com/NordicPlayground...
Hi everyone, I need to send data (coming from many sensors) from a nRF52 to PC via Bluetooth. I have a custom board with nRF52832 and I am using the nRF52 Development Kit...
Hi Team. There is a connection between nrf52840 and esp32-wroom over uart. Uart settings: baud rate - 115200, data - 8bit, HWFC - disable, Parity - excluded, stop bit - 0...
Hi. We have a project we would like to move to an nRF52840 SoC. I have modified the hid generic example to connect with our test software which basically can send and receive...
Hi all!
I want to make my first code in my nrf51 dk (i have an PCA10028). I have experience with M0 and other uC, but i have never play with BT.
Could you guys recommend...
Hi,
I'm trying to improve throughput by increasing the notification buffer number to 6. (SD132, V 5.0.0, SDK14.2)
I tried to follow the sequence charts as well as use...
I'm in trouble because I can't get my expected Logs in WireShark with nRF51822.
[Enviroment] ・I use "User Guide v2.2" and I installed according to this document. ・My PC...
Hello,
I'm using the nRF52832 DK to implement the light switch example in mesh SDK. For this example I'm using nrf mesh app as the provisioner and in this app , to add a...
