I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
We noticed issues regarding BLE activities when running our custom bootloader. It seems that we have located the cause but would like to have approval for that behavior. ...
Hi All
I am trying to find some example code which uses easy DMA over UART using nrf528240..
Using sdk version 15.0. The example which is available by default uses the...
Hi,
I recently bought a nRF51 Dongle (PCA10031) and a nRF52840-DK (PCA10056) and I am now trying to use it for BLE sniffing with Wireshark. I am running OS X 10.14.4.
...
I compiled 4.0.0 in the past and the generated libraries were named "pc_ble_driver_shared_sd_api_vX.dll".
Now I compiled 4.1.1 and the libraries are named "nrf-ble-driver...
Dear Nordic:
My nRF82832 codes based on nRF5_SDK_15.2.0_9412b96 and used s132_nrf52_6.1.0. But I find the Bluetooth signal of nRF82832 can’t be scanned by smart phone which...
Dears,
I am using DK PCA10028 (V1.2.2). Start developing from SDK_12.3.0\examples\ble_peripheral\experimental_ble_app_blinky.
All system configuration keep the same (ADC...
Hi,
I'm using:
nRF52840 Preview DK
Zigbee v2 (nRF5_SDK_for_Thread_and_Zigbee_2)
Segger Embedded Studio for ARM 3.52
Developing on a MacBook (macOS Mojave v10.14...
2017-04-12T06_05_42.374Z-log.txt
Hello,
the example "experimental ble app cgms" (SDK v13.0.0) failed to pair with nRF v1.1.1.
The error code was Authentication failed...
Hi, guys. I'm using two PCA10040 boards. One is using the ble_app_uart__saadc_timer_driven__scan_mode example
github.com/.../main.c
and the other board is flashed with...
Hi,
So I've been trying to get the SIP down to use its most minimal power consumption level to the claimed floor of 7uA or so (I'd take 20uA even), and have stripped the...
Hi everyone, I am using nRF52832 (PCA10040) and ICM 20648. I want to write a I2C aka TWI interface to read accelerometer and gyroscope readings and print them out with TeraTerm...
Hello,
Does anyone know if I can use J-link BASE for programming in factory. I haven't seen any limitation related with it why can't use it for production purposes but If...
