Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
We are currently going in production with NRF52 and we are facing the following issue with RBP on NRF52832QFAAB0.
Basically looks like the processor enters an unknown state...
I have changed the UART or nus_central program in order to be able to connect 2 peripherals to 1 central. Everything seems to be working on the central, no error appears on...
Dear Nordic team,
I am working on ble_app_beacon example code (v-11.0.0-2.alpha) to add the support of DFU (firmware update). I have experience with hrs_dfu example but...
Hello Friends,
im new here. It is the first time with the development of a Bluetooth device. I want to use the NRF52832 Chip.
But what are the biggest diefferent between...
Is the nRF24E1G obsolete?
If so, is there a drop-in replacement for the nRF24E1G.
We currently use the nRF24E1G in a product and have heard that it will no longer be produced...
Hi, I use IoT sdk with my iPhone to get current date and time, date comes in ble_cts_c_evt_t structure, how can I convert it to timestamp, I know that I have to subscribe...
Hello all,
As i want to lower the power consumption, may i know if its possible to connect the supply voltage of ntc thermistor to any gpio of nrf52832 instead of directly...
Hi,
I'm using the NRF52840 Preview DK and want to create my own BT stack with high throughput between NRF52 and other BT devices.
As base I'm using the ble_app_template...
Hi,
I followed the link, gnu-mcu-eclipse.github.io/.../ , to setup my debug environment before. I was able to view the registers. However, I updated my eclipse and the SVD...
I use the nRF52-SDK on an nRF52840 PDK, but if I start a scan request, I don't get the number of scanned channels back in the mlme_scan_conf_t.
I.e. mlme_scan_conf_t::unscanned_channels...
Hi! I need to understand the basic functionality of BLE Mesh.
Please see attached picture.
1. Is it true that a device (eg BLUE) through BLE mesh can communicate DATA...
Dear friends,
Software &Hardware: Power Profiling Application (a SDK example), S132 softdevice, nRF52832(PCA10040), Power Monitor. The measured average current consumptions...
What is the maximum sampling rate of nrf52832? I used the ppi on nrf52632 to collect the signal on gpio. After testing, it was found that when the signal on gpio is greater...
Hello all,
I want to built a coin cell powered thermometer with NTC thermistor.
May I know if I need to regulate the voltage from the coin cell or i can power the nrf52832...
I have a problem with the 802.15.4 software part of my nRF52840 PDK. I wanted to replace our current 802.15.4 hardware parts from TI with the new nRF52840, due to the lack...
