Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello guys,
I would like to execute code once a scan request from any other BLE device is received by the NRF52 using Zephyr.
Unfortunately, I am not able to receive...
Hi everybody,
I have an issue with my application, I want to use the ble with the same antenna that it use in the development board PCA10036,
Could you please tell me...
When I send 512 Byte from my Android phone I received only 20 Byte. How I can received more than 20 Byte? I used example project "ble_app_uart", SDK 14, SoftDdevice s132,...
I am working with SDK 14.0 . I see two "type" of advertising_init() function :
1-
static void advertising_init(void)
{
uint32_t err_code;
ble_advertising_init_t...
Hi
I have successfully run the light control example for BLE mesh. Now if I want to add another server to the network, how do I do it without bringing the server in the...
I am using the ble_app_uart example from SDK13 and something strange is happening. The code without UART part works nice and I can see in RTT that it can discover every beacon...
Hi everybody,
I have an issue with my application, I use the nRF52832-QFAA with the following circuit, when I open the application Nordic 'nRF Connect', I detect the ble...
We have a software application for the NRF52 with BLE communication. The communication part is based on nordic example “ble_app_hids_keyboard”.
We are using Softdevice...
Hi there,
I am using the uart example with SD130 and added neopixel code from GIT to drive the WS2812B LEDs using bit banging.
I want to update the LED every ms. The bitbanging...
I am getting random data while using saadc example to reading analog voltage applied to pin on nrf52840. i want to read analog output from MQ135 gas sensor, I have applied...
Dear all,
by looking at the sdk code, specifically that of s132 component, I understand that the length of the PIN code is statically set to 6 and cannot be changed.
...
We have been using nrf24l01+ for sending few bytes between one Master(Master MCU board) device and many slaves(slave MCU boards). Each time Master Device queries data from...
I installed nRFprobe driver to program and debug my nRF24LE1 chip from Keil. I am using a nRFgo 6700 starter kit for flashing and debugging purpose. I connect ISP connection...
Hi.
We are a Norwegian company trying to create a prototype to monitoring people.
We are already waiting our BLE 5 with ANT capabilities to start creating the prototype...
I am having strange behavior with android application/nrf51 pair
I am normally able to connect to my nrf51 device in a second or two with an android app.
however when the...
