hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
software: ncs 2.5.0, zephyr\samples\drivers\counter\alarm
hardware: nRF52840dk
Step1: main.c is not be r evised!!!
Step2: prj.conf like this:
Step3: overlay file...
Hi Nordic Team,
I am currently working on a project that involves two devices, both using the nRF52840 microcontroller.
Current Setup:
Device A : I have successfully...
hello Nordic
we are working with ncs v2.5.0 trying to migrate to 2.7.0
1. so that there is several rcs, should i take v2.7.0-rc3 or v2.7.0 ?
2. while choosing v2.7.0...
Hi all,
I wonder if nrf9160 has a built-in temperature sensor interfaced with the ADC, that could help to diagnose the internal chip temperature?
Thanks.
I would like to use the Power Profiler app (with PPK II) as a pure coulomb counter for accurate long term (> many days) cumulative device energy consumption without saving...
Hi there,
We have a product running on nRF5340 with an existing workaround that was carried over from an nRF52840-based product, where SAADC readings are prevented from...
Hi Nordic Team, I'm currently working with the nRF5340 Audio DK to broadcast multiple streams, where the receiver can select which stream to listen to. To the reciever, this...
I have an ILI9340 connected to an nRF53 and want to use LVGL in Zephyr (NCS 2.6.1), but I got no label, etc. showing up. Instead, the display is showing a white screen.
...
Hi, I would like to interface an Alliance NAND flash to NRF5340. The flash supports SPI interface. Which set of pins will be a better choice and why ?
I am planning to use...
Hey Everyone, I am new to Nordic and zephyr. I would say I am a beginner. I am trying to setup custom drivers from ST for the lsm6dsv16x sensor. I know most of the time is...
Dear Team,
I installed segger embedded studio in my PC for working with nordic nRF52840-DK. After that I downloaded the nordic license and it was activated.Perfect. -...
If you Edit your build configuration and then add and argument using this button:
it doesn't seem to work. I've tried doing File->Save and using the Build Configuration...
As recommended by the documentation I am using the malloc/free in the common libc branch.
This code (in zephyr/lib/libc/common/source/stdlib/malloc.c) uses sys_heap_init...
I'm trying to increase the SPI speed to drive a DAC that can go up to 50 Mhz. I'm using an nRF52840 DK and SDK V17.
Even if I can set up SPIM3, there is a limit I need to...
Currently I am failing to make my two NRF24 modules communicate, to make sure the two modules weren't at a bas angle to each other to communicate I picked up and rotated my...
