Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi~
I'm using nRF52840 SDK 14.0 to build USB keyboard, the HID type is generic, the problem is:
when is
the keyboard work fine in BIOS but ctrl\shift\alt not work, when...
HI All
Actually I need to send GPS data to own AWS server so from here I setup AWS server and use cloud client sample and follow the step
like
1) change the cloud backend...
I'm using nRF Connect for Windows with a PCA10040 DK to debug my nRF52832 product. Code is using SDK16 & S132
So I currently have one primary GATT service running with one...
I'm attempting to use the pc-ble-driver-py on Windows 10.
I successfully installed pc-ble-driver-py-0.11.4 using pip but when I go to run a Python script using it I get...
Hello,
I am looking at the ble_app_hids_keyboard example in SDK v17.0.2. Where can I find a table that will convert the letters on the keyboard to the hex values used in...
I have a Python script that I am wanting to use to flash our devices at manufacturing that uses pynrfjprog.
When running the script on Windows I get this error:
"FileNotFoundError...
Hi,
We have been working with a Zigbee coordinator, router and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS...
Hi nRF support team, By using the nRF Connect SDK, I am trying to implement an SPI communication with the display module from my nRF52840 dev kit and nRF52840 as a master...
Hi,
we have the need to implement the border router functionality for 6loWPAN in our device using a nRF52840.
Essentially we need to replace the Raspberry Pi in your examples...
Hi, everyone,
I'm trying to assign an SPI End Event to a DPPI channel on nRF5340dk to trigger a counter automatically. However, the value of the counter never increases...
Hi, I am writing a coordinator application based on the zigbee CLI example. I am using SDK for Thread and Zigbee v4.1 (latest if I am right). nRF52840 DK as HW. I want to...
I need to collect data from approximately 20000 points. I want to form a BLE mesh network and collect the data. The sensors may be buried below the ground level about 30 to...
Hi all,
I have a problem with nRF52840 acting as TWI slave. I'm using TWIS. Typical scenario is:
1. Master writes request and ends transaction using stop condition.
...
Hi,
Scenario: 1 Thingy52 device and nRF52 Development kit is in a mesh network, where Development kit is connected to PC via usb cable and also connected to J-Link application...
