Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
Hello,
I need to develop software that realizes the following communication.
[For Central]
Communicates with two peripherals with 2Mbps PHY(short range) and long...
sdk: nRF5_SDK_11.0.0_89a8197 routine nrf51_ble_app_hids_kbd_consumercontrol-SDK11 can adjust the volume of Android phone, or adjust the volume of the laptop
sdk: nRF5_SDK_16...
Hi,
I'm currently porting a project to nRF5 SDK17. Some time ago we decided to use the nrfx module as a fork of https://github.com/NordicSemiconductor/nrfx .
So I synced...
I'm working on a switch device using nRF5 SDK for Thread and Zigbee version 4.1.0 on an nRF52840 on a PCA10056.
I can get my device to join a network, and can see that the...
I see that Apple finally played their card in the consumer asset tracking device space last week. the "Find My" network will be available to third party devices. Details are...
Hi,
I'm working on the Basic example Blink_led.
I would like to change from LED 1 to LED 2. I changed the ch0-pin = <3> in the nrf9160_pca10090_common.dts but now the...
I would like to implement firmware update of nRF52832 through UART from Linux SoM, do you recommend following the DFU procedure or implement custom bootloader? I don't need...
I am using the 9160DK (0.9.0) and testing the PSM and eDRX modes with ncs V1.3.0. if I program the Asset_tracker without any changes I can connect to the nRFCloud.
from...
Hi
Unsopperted device. The detected device could not be recognized as neither JLink device nor Nordic USB device
I believe nRF connect programmer can't fint nRF5340...
On reviewing Zephyr SDK V1.3.0-rc1
I am able to build and run the soc_flash_nrf example as a nrf9160dk_nrf1960 board all works as expected.
when I try with nrf916dk_nrf9160ns...
Hello!
I am working with the nRF9160 devkit and I have encountered an issue.
I cannot seem to properly enable PSM to use the GPS and LTE at the same time.
In the application...
Hello, For our project we were planning on using a 3rd party module MS88SF2 (nRF52840), which schematic snapshot is provided and which will be powered though the li-po battery...
Hi guys,
I am using the Nordic nrf52832 board for my project. One of my goals is to enable the device to read the voltage from the external source. I have already found...
I think I am having a problem with Radio Notification. I am not sure. I have an application where I need simultaneous “Central and Peripheral”. Device only needs to advertise...
