Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi，all:
I use 9160DK to test PSM mode as follow steps with at_client example：
1、set ”AT+CFUN=0“ to power off mode;
2、set "AT+CPSMS=1,"","","10101010","00100001"" to...
Hello,
We're making RuuviTag sensor beacons which log environmental data to flash. Logged data is later read by a mobile phone application over Nordic UART Service.
The...
Hello
I am programming using the nrf52832 module 'MDBT42Q-512KV2' in SDK v17.0.
This works well without any problems in the example ble_app_blink. However, the BLE is...
Hello
I am contacting you to have a little more information concerning the messages which are sent in the examples thread_simple_coap_client and thread_simple_coap_server...
We have performed the DTM mode setup on the ATEX HW variant of nRF52832 chipset using nRF go studio application where the app is throwing an error as attached in the screenshot...
This is more related to the Segger Embedded Studio than Nordic parts or SDK, but I'd like to hear what kind of experience other Nordic users are having with the Segger IDE...
I want to run BME680 sensor example from zeyphyr->samples->sensors, i loaded the project with adding nrf9160dk_nrf9160ns overlay file with the contents :
&i2c2 { compatible...
Hi,
we are using the nRF52840 in a medical ECG recorder. To stream the data as fast as possible we want to use the 2Mb phy. Everything is working as expected under iOs and...
Hello,
I am using Nordic's SES 4.52 with a project from nRF Connect SDK 1.3.1. I have preprocessor definitions I'd like to add to the project to mirror those added on the...
The nRF9160 datasheet tells the reader to refer to the website for Altium files. However, the only files I can find are for the development board. Is it possible to release...
What is the best way to change advertising data for each advertising packet in Mesh SDK's each of proxy / dfu / provisioner?
Using Mesh SDK 4.1, it would be ideal to be...
I have a working code which implements a UART peripheral written originally with SDK15.0
I would like to port it to the latest SDK 17.02
I can get advertisement and I...
Hello!
I have problem updating application firmware with the following message.
In nRF Connnect v.3.6.0 Programmer has been selected.
Log file indicated. INFO...
Hi,
We are trying to develop a wearable device that needs to sync time over a BLE connection and write the time to the internal RTC. We are using the nRF52832 for development...
