Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I sent the AT instruction back correctly with the serial tool sscom5.13.1
I sent the AT instruction error with the secondary function: at_cmd_write ("AT-CGDCONT?," buf,...
1. When using SEGGER Embedded to use Chinese comments, the cursor display will appear abnormal lying each time Chinese characters will move the cursor only half a character...
This is a voltage drop of 3.3V to ~450mV before decaying.
I'm using P0.02 (AIN0) on the nRF52840 on a custom board. This is my config:
My handler function is never being...
Hi,
I am working on handling multi-radio protocols like only 1 radio at a time. ( https://devzone.nordicsemi.com/f/nordic-q-a/63194/when-the-timeslot-extension-could-be...
Hi,
I am trying to disable writes to certain regions of flash memory. But different from the nRF52840 Product Specification, NRF_ACL is missing the DISABLEINDEBUG register...
Hello,
I'm trying to connect a bluetooth device (peripheral) with Web Bluetooth (central). I send an addvertising packet and I can see the device in Web Bluetooth but I...
Hi,
I just bought an NRF51-DK which I want to use with MBED. I need to download the CMSIS-DAP firmware for this board but cannot find it on the downloads page for this DK...
Hi,
i am trying to create a new model for mesh SDK 4.2.0 i am using nrf52832 please provide link or any document for creating new model, i found a link which is for SDK...
I have been using the nRF5 Mesh SDK for development and am in need of implementing single press, double press and long press on the nRF52832. I have seen the nRF5 SDK for...
Hi,
I get the error "[DFU] Remote DFU error: INVALID OBJECT. SD busy? Retrying...." when attempting a firmware update over Bluetooth.
The bootloader, application and the...
Hello,
I'm working on nRF52811, SDK16.0, Softdevice 7.0.1.
Using the pwm_driver example in the SDK, I'm trying to run a simple PWM for an RGB LED. Following is my simplified...
Hello,
I am trying to develop a product on a large scale. I need the last 4 digits of DEVICEADDR[0] as the advertising name for uniqueness. But I am not able to get it working...
I started working on power saving. I tried running the power_off sample from zephyr but there was no change in the current. The current holds the range 30mA to 32mA even after...
Hi,
I'm using saadc library to measure the voltage on nrf52832 DK. also I'm using soft device s132 on the project. I have several questions and will list below,
I want...
