Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Dear,
I got nRF5_SDK_15.3.0_59ac345 package but I couldn't find "Heart Rate Demo for nRF52 DK" source code there.
Actually, I found the HEX file of " "Heart Rate Demo...
Hello,
thanks for providing the very helpfull pc-ble-driver library on github. I really appreciate this! :-) I have an application, based on a nrf52 (a BLE SWD Debugger...
"We are developing some solution where we want to password protect BLE functionality based on individual device. It is very important to connect each device with some security...
Hi, I am following this post to set the TX power level of the beacon. https://devzone.nordicsemi.com/f/nordic-q-a/45871/setting-tx-power-level-in-example-ble_app_beacon-for...
I can not register 2 services 128-bit vendor-specific UUI in one project at the same time. For example if I use services ble_lbs_c.c and ble_nus_c.c the sd_ble_uuid_vs_add...
Hi,
I've got some code (at https://github.com/espruino/Espruino/blob/master/targets/nrf5x/jshardware.c#L1201-L1318 ) where I use nrf_drv_uart to access the UART. I don't...
Currently my colleague and I are trying to connect his stm32 qfpn48 MCU to nrf52840 via SPI protocol.
I tried the sample in SDK and successfully setup a workable dummy SPI...
Is there a sniffer firmware for this board ?
I download "nrf_sniffer_2.0.0-beta-1_51296aa.zip" but it appear that no fw exist for this board.
Is it correct ?
Seba...
Hi, I could not find in documentation function or some command I can call in software to restart the MCU. Is there such a thing, and can this be done? Best regards, Voja
hi ....
i want to test the bidirectional working , i am using uart peripheral example , i have taken the rxd,txd,cts pin from Nrf52840 board interfaced with TTl uart .....
I am working on nRF52DK. This will act as peripheral device and smart phone device will act as central. From my observations i could see 48-bit mac address and GATT local...
Hi
I'm currently doing an internship about bluetooth mesh network.
I'm using the light switch example with a client board and a server board, provisioned with the nerf...
We have an interesting difficulty, whereby after a period of time which varies never longer than 12 hours, often around 6 hours, our application disconnects from the network...
Hi,
I have NCS v1.0.0 on an NRF9160-DK v.0.8.3 and I am trying to run a program written before the SDK update. I can build and flash the program but when I try running...
Hi. I have a multilink central based project running on nRF52840 SDK15.0. I have added code from another example to do advertising as we want the central to advertise some...
