Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
the signal flow is as follow:
TLV320AIC23B(as ADC)——》nRF52832（TX）——》nRF52832（Rx）——TLV320AIC23B（as DAC）
TLV320 works in master mode and nRF52832 works in slave mode. 48kHz...
Hi all,
I would like to know how to cross compile the pc-ble-driver-py for arm target.
Do you please have a prooceding tutorial for this activity?
Thanks in advance...
Hello everyone,
I have both the NRF52840 and NRF52832 dev kits. I was wondering if Nordic has released a packet sniffer to use with Bluetooth 5.0.
Is it firmware/software...
Hi,
i am using ble_app_hrs_c_pca10056_s140(nRF52840) and i want to stop execution of my program and based on button press return i want to continue my program.
i am unable...
Hi!
When I scan for BLE devices using "nrf UART 2.0" application I get a list of all available BLE devices. While running that application a bluetooth is activated on smartphone...
I'm having a few issues getting my application to run. I'm using Eclipse/gcc configured to use managed makefiles, following the tutorial here: bitknitting.wordpress.com/....
Hi
As we know, the mesh network is contained of a number of nodes, so, if we want to get the message of the nodes on the network , i think the node which is connected with...
Hi everyone,
I'm totally newbie, and was following the tutorial devzone.nordicsemi.com/.../ . (I have two board, PCA10028 with a nRF51 and PCA10040 with a nRF52)
and...
Hi,
I have a question about scan window and interval [I'm using nrf51822aa with s130 2.0.1... I performing some tests and I find a use case: If I set both of them (scan...
Hi!
I've found out that, according to this specification
www.bluetooth.com/.../16-bit-uuids-for-members
16bit uuids can be bought by companies.
But, on the other hand...
Hi,
I have an application with an accelerometer. This one communicate in I2C (TWI ). The accelerometer send a "data ready" signal every 20ms. I'm using the GPIOTE module...
Hello,
I'm running into trouble when doing a DFU of the app only using Secure Bootloader SDK13.
When it uses Bank1, it loads the whole image to the empty space after...
We recently decided to use the Nordic nRF52840 . Given the nature of the use (BLE + Thread) of this device we were asked to use Segger Embedded Studio as our development platform...
Hi, i want to set up static passkey for nrf 52 UART example, how can i do that(it many sound insecure but i require it)? I have read many old threads but didn't got a clear...
