Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi,
When I take a vanilla Objective C Xcode project and try to convert it to Cocoapods for an iOSDFULibrary with Xcode 9 results in an unopenable project. You get an error...
Hi,
I am using nrf52832 to scan beacons and then store temporary into two dimensional array.
I made interrupt that call after some interval to send stored beacons over...
Hello,
I got two device with DFU-OTA service enabled
(included device manager and dfu related handlers/files; merged the application, dual-bank bootloader, s130, app_valid_setting...
Using GCC compiler with Eclipse, sdk v14.1, nRF52832, in ESB protocol mode.
The code compiles and builds just fine, all links are ok, but the code below issues a syntax...
One of my nRF52-DK started to act oddly - very brief message in red type flashed up by nRFgoStudio on programming a few times - unfortunately too fast for me to read.
Now...
Hello,
I'm trying to build the ble_ant_app_hrm (multiprotocol) example, using SDK v14.1.0
Here is the output I get, after running make :
Makefile:216: Cannot find...
Is possible use the PPK with a custom board to measure the current usage?
In the pictures it looks like has headers to attach the nRFxxDK modules. but what about custom...
When configuring my Bluetooth Mesh server node to the network, it receives an error and I am not sure why.
I receive an ACCESS_STATUS_INVALID_MODEL error after having called...
Hi,
I am aware of how to use nRF51 sniffer with wireshark.
But in my current project, I am not able to sniff data packets. I am not sure which BLE stack is used in the...
Hi,
we have implemented the experimental_writeable_ndef_msg example from SDK12.2 with Nordic NRF52 on a custom board. Reading the NDEF Message works fine with smartphones...
Nordic nRF52832 chipset
Battery operation such as CR2477 Lithium Manganese primary button cell.
Many application circuits show this microcontroller used with a button...
Greetings,
One thing I've noticed is that if I enable the RTT nRF_Log messages in the bootloader, then the RTT messages that are being sent out in my application do not...
Hi,
i have recently bought a development kit for the nRF24LE1 chip. Untfortunately there was no CD included, as described in the following user guide.
data.icbank.com/...
The nRF51822 Bluetooth Smart Beacon Kit has P0.09 and P0.11 connected to the programming connector P2 (Pin 3 and Pin 6). From the User Guide :
Can I use them as UART...
I have a Rigado BMD-300 Evaluation Board with a BMD 301 module attached. Using the Texas Instruments SmartRF Packet Sniffer, I see the message being broadcast approximately...