I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi DevZone
Does the SWF switch at the PCA10040 automatically switch to the antenna I have put on my connection probe? ( www.digikey.com/.../1775923)
Thanks in advance...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Sir,
I am working in nRF52832 board with pca10036. I want to know whether the board supports a loopback control in SPI mode. I need to try for transmitting and receiving...
Hello,
I'm trying to use NFC module on nrf52382 chip (DK PCA10040) and prepared firmware "nfc_text_record_pca10040" from examples of SDK v13. After flashing the Mifare ultralight...
Hi,
In the nrf52.h, SPIM_RXD_Type is defined as below.
typedef struct {
__IO uint32_t PTR;/*!< Data pointer */
__IO uint32_t MAXCNT;/*!< Maximum number of bytes...
i am working with Nrf52 + Visualgdb complier.
nrf_drv_gpiote.h contains designated initializers which aren't supported by C++. I'm including all SDK headers inside an extern...
Hi,
I would like read a long characteristic.
I know that I have to use sd_ble_gattc_read and I have to multiple call this function.
But I don't know where I have to call...
Hello,
I want to implement some kind of control point. This means, that I want to handle BLE write events to some characteristic. I've seen that the payload of the ATT...
Hi,
i tried to find an example with SPI which describes the connection between two nrf24LE1, one as master and one as slave, but i could not find anything. I need the following...
Trying the ATT_MTU Thourughput Example with SoftDevice:
nRF5_SDK_13.0.0-1.alpha_055eef3/components/softdevice/s140/hex/s140_nrf52840_5.0.0-1.alpha_softdevice.hex
on...
Hi, I just want to know,
Is it possible to develop a device that advertise normally and be connected by mobile, but the device must always send the eddystone-format advertising...
I'm interested in adopting nRF52840 as a mesh networking + Beacon device. It is my understanding that the Nordic SDK for mesh will only be released after Bluetooth SIG releases...
hello everyone:
I work IPv6 over BLE example on both Raspberry pi ,this pic is 6LN (CoAP Server)sending IPv6 over BLE packets to 6LBR(CoAP client) and I use tcpdump to...
Hi,
I'm testing the multi-link functionality.
I want to manage the connections with connection handler.
But, p_gap_evt->conn_handle passed thru on_ble_evt(); and p_ble_nus_evt...
