I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Hello,
I built peripheral_hr_coded sample and looking into the partition manager report (I trucated the output):
What are the s0_pad and s1_pad?
What are the EMPTY_0...
Hello,
I am developing a FreeRTOS project that uses nRF5340 MCU. For the inter processor communication I would like to make use of the RTOS-agnostic RPC library (sdk-nrfxlib...
Hello fellow bit jugglers!
We are developing an application for a nRF52805 on a nRF52-DK board, using NCS.
NCS version: 1.7.1
Zephyr version: 2.6.99-ncs1-1 (commit...
Hi:
I have a BLE HID remote control that needs to be connected to the HID central(nRF52832).My SDK is NCS v1.8.0.
When I try to connect with the HID remote I get the log...
Hello,
I have to make the external flash on the nRF9160DK work with the nRF9160.
From what I understood, the default settings are that the external flash on the board...
I have beacon that broadcast its name with type 09. I cannot get it while scanning of nrf_uart_c (adv_report).
I assume I need to activate scan_req and then parse the response...
I need a constant acquisition time for my SAADC. In my experiements I see jitter in the acquisition time, so I started debugging with PPI to ensure no Interrupts are making...
Hi,
I am trying to enable event length extension on uart example provided on the sdk. I look for information on how to done it and i found links like that:
https://devzone...
Hello，
I am using ncs1.7.1, qspi + mx25r64 external flash ota it works well, but I don't know how to change qspi to spi.
I need your help thanks
I change the parament...
Hi Nordic,
I am working on a raspberry pi based gateway which has Thread Border Router and edge node functionality. I have setup the OTBR on the gateway and I have manage...
Hi,
how can I change the standard LED_0 output from P0.17 to P0.03? I am using SES, toolchain 1.8.0 and the nRF52DK board and I would like to flash the sample code to a...
Hello! I have WF200 wi-fi chip connected to the nrf52840 through SPI. I configured bare-metal example code of WF200 chip to work with nrf-sdk and this example (basic CGI server...
No connection after disconnect with Android App Nordic Uart Service until mac-address of smartphone changes
Multilink multirole software developed in SES studio.
Other...
Hi I have a product that uses an Nrf52810 in a Raytec slave module. I am able to successfully send and receive packets of data using your UART app in the nrf Toolbox
I would...
