Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Nordic NUS - uart service; both SDK 15.3 and 17.0.2. Packet loss on repeated BLE disconnect - connect cycles; seeking clarification of my understanding.
"If there are untransmitted...
Hi, teams.
I am testing nRFConnect 1.5.0 with nRF52833DK.
Recently, I noticed "Direction finding connectionless beacon" example in latest repository, and copied it to...
Hello Team Nordic,
We are using nrf9160 DK with nrf connect SDK 1.5.0 and mfw_nrf9160_1.2.3 modem firmware .
We are currently evaluating the FTP AT command set and according...
Dear Sir,
Moving to zephyr new installation 1.4.99
Configure SPI1,SPI3 . I can see the SPI configured in zephyr.dts
spi3: spi@b000 { #address-cells = < 0x1 >; #size...
Hi,
I am using the stts751 temp sensor with nrf52832 for temp data logging for short time. I want to save temp data in the internal flash memory but I didn't find any similar...
I followed the instructions in https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.3.0%2Fsdk_config.html
and pasted the appropriate text...
Hello,
I have been trying to get the ADC working but for some reason, the adc_read function throws an error of invalid argument ( -EINVAL (-22) ). The adc_channel_setup...
Hi all, I have tried to follow the step to get up and running with my new nRF9160-DK, however, I am not sure if the Application FW has been successfully updated (how would...
Hi,
We are using a bootloader/DFU based on the secure_bootloader example with USB transport from SDK15 and It works fine.
Now, we are trying to add the possibility to...
hi.
i use nrf52840 to d evelop a keyboard .i connect and be bonded by a pc,now i want to delect to the bond info of the pc,and after this ,my adv cant be scan by this pc...
Hi Nordic Tech Support team,
One of my customers is having some problem with UARTE implementation. They used the ble_app_uart example ( pca10056 with SoftDevice 113 )...
Hello Everyone,
We are developing one custom device using open thread protocol.
We are using SDK - nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 and Dev-kit - nRF52840...
IN Establishing the friendship,I received the following error
/** The Low Power node was not able to send transport command due to internal fault. */ NRF_MESH_EVT_FRIENDSHIP_TERMINATED_REASON_INTERNAL_TX_FAILED...
I want to send ADC data over bluetooth. When I searched, I found the following contents.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsds_s132%2FSDS%2Fs1xx%2Fble_data_throughput...
I am using the nRF51422 development kit with the SDK 11. I am trying to run the proximity application located in ble_peripherals. When the project is build I am receiving...
