Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi
I'm confused by the concept of switching slots and sampling slots, or at least the way they are presented as being interleaved. For BLE, I believe that they are required...
I am considering using a high-Q BAW filter to drive as near the band edges as possible and roll-off noise beyond.
Source of my interest:
https://www.qorvo.com/design-hub...
I am using nrf52832 SDK14.2 development, now the system will generate some strange exceptions, I am worried about the stack overflow, is there any way to confirm whether the...
Hi All
We are using nRF9160DK and want to send data to the cloud (Adafruit or Thingspeak) using MQTT protocol but we do not have NB-IoT
Network in Our area so it's possible...
To the kind attention of Nordic support team,
I've been reading in this post:
https://devzone.nordicsemi.com/f/nordic-q-a/44042/using-nrf52810-with-gzll_nrf52_arm-lib...
Hello,
I need to validate my selection for crystals working with the NRF52840. For the 32.765kHz crystal I have chosen the 9HT12-32.768KBZC-T from TXC Corporation. For the...
i have test with RTC using nrf_calender.c.
It will prints output data on terminal window.
But, I didn't recognize the actual data.
Output data is mentioned below,
...
I am attempting to use libmbedcrypto.a from the Thread/Zigbee SDK version 3.2.0. I am linking it from:
external/openthread/lib/nrf52840/gcc/libmbedcrypto.a
and yet...
HI,
I want to implement the software security to NRF52832 such a that no one should be able to read the memory or tap the data during Bluetooth communication.
Regards...
Hi,
I am trying to interface tlv493d with nrf52 dev board.
I have taken driver code from infeneon
https://www.infineon.com/cms/en/product/evaluation-boards/tlv493d-a1b6...
Hi
I face ble disconnection issue.
we use external crystal 32.768khz. However, when I check it , the load cap is wrong. It should be about 9pF but it is 1pf.
The frequency...
Hi,
When factory resetting the flash storage, I delete all records, and then call fds_gc(). However, the page that's used for garbage collection still contains a copy of...
Invitation : The provisioner invites the unprovisioned device to send its provisioning capabilities information.
Firmware version from this examle: https://github.com...
Hi.
I've bought the nRF52833 DK and I want to use it with Mbed OS.
But I'm not getting it to work. If I compile the "mbed-os-example-blinky" program for target nRF52-DK...
