Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi,
I am a little bit confused about the different supported stack for the nRF52833 when using BLE Mesh. With the current example, there is only support for the S113. Can...
I started a timer on the nrf52840 and the SDK is nRF5_SDK_15.2.0_9412b96, but I haven't never receive the callback message after the time. What's the reason?The code is as...
Hello ,
In this scenario, I have to measure the time interval between the START and STOP pulses generated by a peripheral device connected to nRF52 DK. The thing is START...
Hello!
I am currently using a module called BLENano2 (nRF52832). SDK15.0.0 is used and the editor is "Segger Embedded Studio v4.16".
Finished writing the program that...
Hi,
I tried out the light switch example on a nRF52833 and it seems not to be reliable at all. So i connected the debugger and saw, that in access.c,
in packet_alloc_and_tx...
Hi all,
I am trying to use nrf52840 dongle as hci_usb with the very simple task: scan
Host is Raspberry Pi with BlueZ
Controller is nrf52840 dongle with firmware hci_usb...
Hi
I want to move DFU at the application level. Is this possible? I want to move DFU at the application level because of my project requirement.
1. In my project, I have...
Hi, I am trying to get the BLE values on Thingy91 (PCA20035) . And I have followed the
devzone.nordicsemi.com/.../217018 I have ported the diff (nrf and zephyr diffs from...
I am using built-in DTLS for encrypting my UDP traffic. In order to save expensive data quota and reduce battery drain, I have to make use of session resumption, so that I...
Hi. I have a question about Bluetooth 5.1. I just want to know what the main difference is between a Bluetooth 5.0 and Bluetooth 5.1 chip.
Is it the hardware or software...
I am developing a firmware on a nrf52840 board with FreeRTOS. Unfortunately, due to a mistake during the development process, the board misses the XTAL 32,768 Hz.
Is there...
Hi Nordic:
I want to build a raspberry connected to a 52832 board via uart,
this raspberry pi with 52832 board need doing secure DFU to remote BLE device, the raspberryPI...
Using the nRF9160 on the Verizon network we are having some issues with eDRX. Specifically sending data to the device from our MQTT server.
We have configured a eDRX interval...
Hi,
I am working on nrf52 msc example. I am required to use internal flash for msc. In example there is support for ram, sd card and spi flash. I am required to use internal...
