I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
My queries are:
1) In code I just changed...
Hello,
I have queries on Sniffer functionality.
1) Using nRF52840 USB dongle whether we can sniff BLE 5.0 packets.
2) Using nRF52840 development kit whether can I...
Here's is my device profile:
Running on SDK 15.2.0
FreeRTOS
Custom board, based on NRF52840
Powered by a 3.5Ah battery
Using CLI utility
Using the following...
Hello, we are developing a BLE application using SDK 5.2 and softdevice 6.2.1 (we are aware this is old, but we still have to support it).
We actually use Keil IDE 5.10...
Hello. I'm reviving an old project (nrf51 and 12.3.0 SKD with sd130 2.0.1). Unfortunately bootloader is not working properly. It worked just fine at the beginning of the year...
Hello:
GPS and LTE can't work at the sametime currenty with 1.0.0 modem firmware.
You know that EMC test need GPS and LTE work at the same time.
Will GPS and LTE work...
Hello, I would like to utilize UART and NUS to both send and receive data using the ble_app_uart example as a starting point. I have tried connecting to the nRF52 DK with...
Dear All,
I am using UART read write operation along with the system off mode. So, usually nRF9160 chip goes to sleep and wakes up when it receives something on UART and...
Hello Nordic support team,
I'm working with NRF52832 development Kit. I want to transfer our firmware application (OTA-DFU) from nordic central device to nordic peripheral...
Hi, I am trying to get RSSI values using BLE module on nRF52840(pca20035). But I could not see possible way to get the RSSI values on Nordic Thingy91(nRF9160) Please map me...
hi all
i want porting qpc with softdevice. it need set SCB_SYSPRI exception priorities with PRIMASK bit or the BASEPRI register for critical section
can anyone give me...
Hello,
I would like to update an nrf52840 with DFU (usb-serial). On windows I can use nrfutil. But how to proceed if I want to do that from another microcontroller?
Is...
Hi,
I am working with nrf52840 DK and sending real time sensor data to nrf toolbox using ble_uart. I would like to store adc output in flash and then send it over ble uart...
Hi Devzone
I tried to use saadc with 4channels. when I use this without fpu_fft, It prints correct value well.
But, when I insert the fpu_fft and run it, after a while...
Hello
I have a question about SIG certification. As far as I know, to get SIG certified, I need to download the DTM firmware to the board and pass it to the certification...
