I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello Nordic, I've been searching the forum and the SDK for code examples that specifically use Bluetooth 5; could you direct me to that code? Many thanks in advance for your...
I am now based on nrf52832 SDK14.2 development, I tried to use the PWM driver and timer to drive the corresponding two IO port an irregular waveform, I originally thought...
I am using the Hackable kit which has nrf52832 to control a servo motor and read accelerometer(AXL335) readings through a iOS app. I am a novice when comes to embedded. I...
Hello, ererybody!
I use nRF52832,have a development board.
I was testing the adc module,using the ANI2 channel,I measured the ANI2 channel voltage to the ground,find it...
Hello everyone,
now i'm working with nRF52840 PDK( Engineering B ) and i migrate my project from SDK 14.1 to SDK 15. My starting point is ble_app_template and i want to...
Hi!
My setup:
* nRF52 DK (let's name it N )
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
* two android smartphones (let's name them A1 and...
1. nrf51822-qfaa
2. sdk10.0 & sd8.00
Q:
If the MAX_CONN_INTERVAL is set to greater than 200, NRF_ERROR_INVALID_PARAM will be returned when called sd_ble_gap_ppcp_set...
This post had a discussion on using one button but the first reply suggested a buttonless solution. So now I'm not sure if one button dfu is best if same button is used for...
hi,
i am doing a project where i have to exchange strings between nrf52832 as peripheral and andoird smartphone using nrf connect app, in this project data security is a...
Hello!
It's the first time using Nordic devices so i´m doing some SDK examples and trying to merge them. I'm using SEGGER Embedded Studio. Right now i´m using ble_app_blinky...
Hello,
I'm usign nRF52832 IC and SDK5. I want to awake the sleeping MCU by NFC and pair with BLE. In short Pairing device address should be transfer via NFC. There will...
Hi all
i am using SDK15, nrf52832 dev kit and s132 version 5
I followed the below steps:
1)Flash the softdevice
2)Update the generated dfu_public_key in secure_bootloader_dfu...
I am developing a firmware and connected a spi LCD to nRF52840, but I got the max speed only 8 MHZ, in Datasheet is 32 MHZ max.
Which speed of the SPI master is max ? (I...
I'm getting a disconnect reason of 0x3D / BLE_HCI_CONN_TERMINATED_DUE_TO_MIC_FAILURE during a connection attempt. It does not happen for all my phones except one. It appears...
