I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I'm trying to get acquainted with the NRFX_GPIOTE driver by writing a program to do the following:
initialize TIMER to generate three compare events:
channel0 compare...
Hi,
Working on a product with a couple to sensors with i2c communication. Are normally able read values from the sensors, but sometimes the i2c bus seem to be down. No more...
Hi,
I used sdk11 and sd130 at a 51822 project, it is required to be paired with a key for both andriod and ios, everything is fine but the dfu on andriod, I used nrfconnect...
SDK 14.2.
Application Timer Library
I had a question regarding the Application Timer library and the way it checks for timeout handlers. In the documentation, it says...
Hi, I have problem with nRF51822. I've bought cheap China miniboard with this chip. I can program some examples (precompiled HEXes) with J-LINK and they works correct, but...
Hi,
I want to make a program in order to assing functions to the buttons and manipulate movile phone apps without making any app or configuration into the phone.
What...
Hello,
I've a process, let's call it P1, that sends I2C instructions for a LED driver (it's like an infinite loop of I2C instructions for registers management that have...
Hi all,
I want to make touch button by my NRF52832 board . I am trying Csense_drv example but The value of change is constant when I log on UART . LED flashes continuously...
Hi Team,
I am working with Nrf24L01 chip with ATMEGA328(ATMEL C code) i made separate TX and RX module it works fine. But i want TX and RX in same module i done coding but...
Hi.
I am using SDK15 and want to control keyboard and mouse using HID with nRF52840.
I used the HID example to verify that the keyboard and mouse work when the button...
Tools in use, etc:
nRF5_SDK_for_Thread_and_Zigbee_v1.0.0
RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha
NCP example located in <InstallFolder>/examples/thread/ncp/uart...
I use nrf52832 qfaa b017351o ,some ic can run sdk11 dfu demo but some ic can't. Demo location .\nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132...
Hello,
We have a custom board based on nRF52832, built an application base on SDK V15/ble_app_uart
It works fine with Android: we can send string over BLE but it doen...
Hi everyone,
I changed the example ble_app_beacon from sdk 15.0.0 sd132 to be able to scan beacon besides transmit. It works well to scan beacons and I can get their UUID...
