Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I'm a beginner in programming Nordic uC and I would like to know how to enable the watchdog in my application. Are there particular functions to call?
Thanks!
Hi,
We have a prototype application which requires an NRF52 based peripheral to be inside a metal cabinet and to connect via BLE to a central while maximising the link...
When calling access_model_application_bind() , NRF_ERROR_NOT_FOUND is returned?
I have had this working before, but after adding another server model I am getting the error...
Hi,
I am implementing modified DFU for nRF52832 which uses external flash memory. If power loss occures during update process, device then start update process from the...
Hello sir,
I am working on my final PCB design using nRF52832 chip. As per your reference Bill of material i use same part number for all components recommended by you. But...
I have a custom board with the nRF51822 QFAA . Schematic:
In order to compile the firmware, I'm using MinGW . As you can see, I'm also using the SDK 12.3.0 .
Finally...
Hi,
I am using nRF52832 and softdevice is S132 adk13.1. My application is read 3 ADC channel one by one and send this value to android app using NUS. For this i have use...
Hi,
We are performing data transfer using NUS service (BLE-UART).
Data passed is a 11-character string.
READ and NOTIFY permissions are provided for Tx characteristic...
Hello,
I am designing NRF52832 based board. I followed the exact reference layout suggested by Nordic except via position. I moved few vias during routing. Is it necessary...
I am using segger studio and jlink to program my nordic thingy 52. I followed the documentation and
Build the program
Connect to Jlink
Erase All
Debug->Go ...
Hi!
nRF52. S132, SDK13.
I try to use ble_dfu_send_hex example.
what shoul I do first?
via nrf gostudio load SD. correct?
Which SD? from this folder (dfu_test_softdevice_s132...
I get the mesh SDK here: http://www.nordicsemi.com/eng/Products/Bluetooth-low-energy/nRF5-SDK-for-Mesh/(language)/eng-GB
But I don't know how to add pwm to the light_switch...
Hi all,
I use the nrfjprog 9.7.1 and unfortunately I was used the --rbp command on my nRF52832 and now it's impossible to execute --recover command.
The nrfjprog log shows...
Hi,i have some problems when develop with experimental_ble_app_buttonless_dfu project in sdk12.3 on IDE embedded studio (MAC OS).
I follow this link text to develop.when...
Hello,
Some problems I meet when I try to use spi manager in ble_template example to read "who_am_i" register of LIS2DH12. The environment is set as below:
nRF52832...
