Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
How do you do
Using E: \ Nordic \ nRF5_SDK_12 2.0 \ examples \ ble_peripheral \ ble_app_uart ble_app_uart routines, join in routine PWM program, cell phone bluetooth connection...
I am trying to record the time on nRF52840 with s140 softdevice.
I used APP_TIMER to setup the TIMER and app_timer_cnt_get to get the count. And then uint32_t app_timer_cnt_diff_compute...
Hello,
We are using ble_app_uart example for both central and peripheral. We can succesfully send and receive data.
We deleted the is_UUID_present control. And then...
hello
i am working with simple ble mpu example it is working fine but when i am trying to connect nrf52 DK with my android phone over bluetooth it is showing
the device...
I have analysed the light switch client and server example apps where the light switch is also the privisioner.
They both start and initialise a bit differently although...
Hello,
I used translation software.
I used the function to enable DCDC mode
I used sd_power_dcdc_mode_set ().
I want to use the optimal mode for power supply voltage...
Hello,
i'm using an nRF52832 as a Bluetooth to UART bridge, similar to the APP UART example.
Another controller (Cortex M7) is connected to the UART. I'm using UARTE with...
Hi,
I'm using two sensors with the same device address through I2C.
each sensor is supposed in a specific period of time (not working together), each sensor has a different...
I am writing a mesh beacon application based on Mesh SDK v0.10's beacon and light switching examples.
A very kind Nordic employee has provided an example on how to combine...
I'm having a problem with using all the memory in the nRF52 Thead SDK 0.10.0. Namely, even if I run one of the smallest examples (e.g. aes one from crypto examples) the flash...
I am using softdevice132, sdk 14.0, pca10040 dk,
when i add nus service to the dfu example, it is not working. there were also some warning about iram start address, which...
I just saw the news that Nordic is providing a free Segger Embedded Studio IDE and the sample projects from SDK 14.1 include the Segger project. I downloaded it and the license...
As I understand we have some problems with time sensitive actions while using softdevice with active ble connection. So here's my questions:
Are there some possible...
Hi All,
I am working on pca10040, nrf52832 and s132. I am using ble_app_uart and sd card, where i want to transmit data received over ble to the sd card.
Can you help...
If there an example on how to test the Raspberry PI border router ( infocenter.nordicsemi.com/index.jsp and some nRF52840 Preview DK together with the official Thread commissioning...
