I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I have used Arduino for some time and i am very new to NRF. So i am struggling with any thing i do. But i am really motivated to learn it.
Completed setup for eclipse to...
Hi, I am designing a PCB which consists of an analog circuitry (microphone + analog front end) and the nrf52832 chip. I am using inbuilt-ADC of this chip to sample the acoustic...
I use this demo [nRF51_SDK_10.0.0_HID_DFU_090216.rar] (/attachment/27e0b68cff3ffe4959299fcae336e844)
change rep_map_data[] add mouse and Consumer,but restart is no work ...
Hi,
(I'm a computer scientist, please be kind)
In the below attached image, I have collected the data outdoors (so no signal reflection or signal fading) from a single...
Hello all,
I am using nRF51822 BLE SDK 9.00 PCA10028. I want to configure the gpio pins as input to sense the voltage as high or low. how to configure it please suggest...
hi
i'm developing to nrf52832, sdk14.0 version.
for example, ble_app_uart project..
NRF_LOG_INFO("UART Start!");
printf("UART Start!");
-> In serial program,...
I have an application that do SW download to STM32L151 processor using NordicDongle with MasterEmulator.dll (Version 2.1.13.14)
It works good on my desktop windows 10 computer...
Hello,
we are trying to test the mesh functionality with nrf development kit. We erased the flash on the dev kit and we programmed it with softdevice version s132v3.0.0....
As stated in the topic. We use BLE to simulate UART. As for now, we have defined our own UUIDs but there would be more straight forward to use the well defined and used one...
Hi,
I have known your board support jlink ob；I want to debug through it ;
I want to know if i need to buy the software-license from SEGGER ？
and if i need buy the software...
Now facing the problem "After disconnected, the electric current increases"...
I think softdevice is working hard even after disconnected when connecting once.
Could you...
Hi,
I'm trying to write unit tests and have arrived at the point to write tests for ble characteristic addition to a service.
To offer some background, I have written...
Hello,
I use NRF51822 and I try to output UART message onto hyperterminal program.
but every message I send it contains "APP:INFO:" in front of the message.
like...
