Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I'm using nRF5DK PCA10040.
And, working on nrf5_SDK_for_Mesh_v0.9.2-Alpha.
I need to enable both of Bluetooth mesh stack and BLE stack.
mesh stack for mesh communication...
I added uart service ( here and here )
and I think in part of ble everything goes well. I have blinking led1 and can see all my services.
Then I tried add uart part.
After...
I have a custom board that has a nRF52832 device (receiver).
I am scanning for remote beacons (also custom boards with nRF82832).
The result is that I obtain the MAC of...
Hi I use 4 characteristics in peripheral and central. When I write to one of the characteristics in the peripheral, I read it using sd_ble_gattc_read in the central. But,...
Hi,
SDK14.0
nRF52832
I am using the dfu\bootloader_secure_ble example as my starting point. My goal is to create a very simple bootloader (with none of the dfu stuff...
Hi
We are trying to use the uECC library file (micro_ecc_lib_nrf52.lib) with our project that is built in Kiel. We have followed the instructions found here using the open...
Hello,
I'm using SDK 132 (v5), kiel 5, SDK 14 and the nrf52 dev board.
I'd like my application to have multiple Offical Services (Heart rate, Humain temperature,...
Hi,
For my new project, I copied the linker script and Makefile from examples/ble_peripheral/ble_app_uart/pca10040/s132/armgcc to a folder and changed the SDK dir and project...
Hi All,
I have developed a device using the nRF51822, and the connection interval is set to ~1000ms.
When reading a characteristic from a Raspberry Pi, we are timing...
Any updates on this from anyone? Please advise
Hi,
The i2S microphone that I am using requires a over sampling rate fixed at 64 therefore the WS signal (LRCLK on nrf52...
Hi community, I'm running a 51802 on my custom board with no other parts on it, except for some buttons and leds directly connected to GPIO, and a DC/DC converter which feed...
The term 'slot' is used in the context of the Eddystone beacon specification.
I cannot find a definition of that word.
For example, the sample app from Nordic says ...
I set up an account a few days ago on nordicsemi.com and today it's rejecting my login. I then requested a new password which was sent to my email but when I copy and paste...
I am studying how to update the firmware through BLE at the moment. I used the example project of "ble_app_buttonless_dfu", but I am having many questions that I don't understand...
