Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello,
I have two devices sharing an I2C bus. These devices are the MAX86150 and the MLX90614. DMA is being used. I2C is running at 100 KHz.
After initializing both...
Hello,
I'm currently working with sdk 11 on nRF52832.
I'm trying to acquire 20 value from SAADC every 10ms during 300uS.
I think that the rate is too high because...
Hi , why I can't have an update of my bootloader ? Here is the script I use to generate the .zip file :
nrfutil dfu genpkg --bootloader Bootloader.hex Boot.zip
The...
i have RBL nrf51822 ble and i want to try it with BLE Sniffer. i flashed the nrf sniffer hex file by drag and drop to my dongle but it doesn't show anything. only it shows...
Hi Everyone,
I am working on a hobby project with nRF51822 which needs me sample upto 4 signals reliably at 500Hz each at 10bit resolution. I have read through few posts...
Hi all,
I have two nRF52 connecting, transmitting, disconnecting and sleep mode when are in normal operation, now I am experimenting a randomly error code 8 when calling...
Dear Nordic Team,
Meanwhile, I've burned through a week finding a solution for this problem.
Now I am out of ideas where to check for problems.
My application:
I...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
I'm trying to flash a nRF518122 with a St-Link V2 programmer via Open OCD.
The process seems to goes smooth, but comparing the number of written bytes to the actual HEX size...
How is BLE_CONN_HANDLE_INVALID changed in multiple services
I modified the ble_sdk_app_proximity example. I added x3 services, based on the BLE Characteristics, a beginner...
Hello
im building a project for discovering infections through temperature sensors, so im modifying the heart monitor sensor examples (central and peripheral) in the sdk...
Hi
I am developing an applicaztion with SDK 13.0.0 and S132 for nrf52832
The version of the softdevice to be used with this SDK is 4.0.2, and I need access to L2CAP layer...
First,the meizu phone can dfu successfully in the dual bank mode,
So do the 360 phone.
But in single bank DFU,this two kinds of phone failed,
So I make the programm enter...
I'm designing custom board with nrf51822 SOC & using buck-boost converter for powering nrf chip, If I don't add inductors in DCC line how it will effect my custom board. ...
