Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
My application is based on the ble_app_uart demo. I want to get the BLE approval from the lab. The lab want me to tell them the Bluetooth profile of my application. How can...
Hello,
I am trying to interface the STPC16CPC26 with the NRF52832. As per the datasheet of the display driver, we have to toggle two IO pins from the NRF which shall be connected...
I want to write protocol stack and my program to 518222 and now need the manually download device or the automatic download device. can you offer me the communication ways...
Hello
i am using Nrf52dk. i have Visualgdb.
i would like to use the Nrf5 IoT sdk in visualGdb.
i have some question. is that Nrf5 IoT sdk will support the SysGcc toolchain...
good time dear Engineers!
faced with a problem of S132 nRF52. ADV data of packet lost.
I compared the RAW data according to screens below:
If I use nRF Connect ...
Hi, Nordic
I see this question: devzone.nordicsemi.com/.../ , I follow it, then I can see log in J-link RTT viewer.
But when it work, I find after some time, the old log...
Hi would like to evaluate the consumption of my pcb in connected mode using a nRF51. For that I use the nordic excel tool : "APM_nRF51822_S110_v3 0c.xlsx".
But I really don...
Hi,
I am trying to save some data in flash by using the Flash data storage.
However, everytime I try to write data to the flash, the module returns this error code:
FDS_ERR_UNALIGNED_ADDR...
Hello,
I'm making bootloader(nrf51822xxAA SDK12.1.0 and SD130 version).
I have some problem in micro-ecc installation.
To install micro-ecc, complete the following...
Hi, I have a problem with DFU OTA.
I use nRF Toolbox's DFU to upload nrf51822 QFAC, most times it works.
However several times, after the app altered "** bytes transferred...
Hi,
I want to generate a 2.048MHz clock on one of the IOs of nRF52832. Could you comment on following questions?
1- Can I generate this frequency (with no load on CPU...
Hello, I work with some ADC 24-bit (HX711) and for getting data from that I need after low level on first gpio pin to fed 26 pulses to that with time period about 1us on second...
Hi,
I am using ble_app_uart_c_S120
How can i support more then 1 bonded connection?
i try:
#define DEVICE_MANAGER_MAX_CONNECTIONS 7
#define DEVICE_MANAGER_MAX_BONDS...
What's the correct settings for nRF51822 CEAAE0 (0x0079) with dfu example in SDK v11 ?
I believe the chip I am using is a 16KB ram 256KB rom version, but not sure 51422 or...
