Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Dear All,
I have question regarding advertising in NRF51. I measured the power that be used when advertising using osciloscope and set the advertising interval of NRF51...
I'm having this event and I'm not sure what are the conditions required to trigger it, also what does it mean exactly since the documentation does not say more than a line...
I had attended the Nordic 2015 Tech tour in Helsinki and it was very nice of Nordic to give away nRF52 DK to all attendees. So far, I've been busy working with nrf51 but today...
I follow this instruction to turn Raspberry Pi into an IPV6 router on IPV4. My raspberry pi works well after I add nameserver to /etc/resolv.conf.
But other device in my...
I am experiencing an error that I can't figure it out why it is happening and where to go and try to fix it.
I am using the subscriber implementation on my nRF51, Raspberry...
I see in multiple examples of NRF51 SDK:
#define APP_TIMER_MAX_TIMERS (2+BSP_APP_TIMERS_NUMBER) /**< Maximum number of timers used by the application. */
but it is...
In ble_gatts.h, I see:
#define BLE_GATTS_FIX_ATTR_LEN_MAX (510) //< Maximum length for fixed length Attribute Values.
#define BLE_GATTS_VAR_ATTR_LEN_MAX (512) //< Maximum...
Hello Everyone,
I have been working on the NRF51DK by using proxmity examples as reference when i added the static passkey for the connection security it is working well...
Hi, i am new to embedded system.I want to use nrf52 DK as master and connected with two slaves by two spi channels? is it possible to achieve on nrf52 DK.
1>How to set up...
when i turn on the Keil, they have showed error to me
"Install missing Software Packs?
NordicSemiconductor.nRF_ConfidentialDeviceFamilyPack"
then i try to re-intall familypack...
Hi,
I wanted to know How can I find if any application on any platform(Central device)is listening to my advertising packet or not !!
The whole idea behind this is to...
Hi,
I have made a few custom boards based on the nrf51822 but on my latest design, I'm having a new problem that I haven't seen before. I have read the posts in the forums...
hi everyone,
i'm testing an application on pca10036 board where i need to create a large buffer. i use Keil v5 as dev. environment. My buffer is static and global, therefore...
I'm using 2 nrf51 DKs one as central and one as peripheral. I'm wondering if there is a defined time that a write takes to be registered on the peripheral?
