Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I could scan/detect Beacons, and I could update the configuration without any problem with the nRF Beacons app. The issue is that the configured Beacons are not detected in...
Hi,
I want to use the nRF51 dongle with the Master Control Panel.
I found in the nRF51 Dongle User Guide that the Dongle will run with the Master Emulator firmware, but...
I don't expect the Nordic engineers to know this answer but I'd like to hear from other devs out in BLE land...
Have any of you encountered truly horrible BLE PHY-level...
I am using S120 device to receive advertising from S110 device and need to get the exact time + sender's address information at Radio End Event.
I use PPI to start Timer1...
Hi,
I'v try to use the sd_power_system_off() and without successful.
The power consumption will be 200~230uA around.
My device:
Call the system off when ADV._TIMEOUT...
Hi
I am trying to make a ble central with s120 on a pca10001 board.
My problem is that it sometimes take a lot of time (up to 10 seconds) to find the client when i make...
Hello Nordic guys, help requested !!!
Error while connecting to USB port the new development boards, DK and DONGLE.
Error is " OS X unable to repair JLINK disk ".
...
Hi,
is it possible to use Nordic SDK with nRF51822 to have capacitive touch sensing with 2 dsital inputs, just as the mbed or avr library capsense?
MBED: developer.mbed...
Hi, i have a strange issue on connecting nRF24L01+ module to Arduino pro mini. I use arduino pro mini, nrf24L01+ module, 3.7V 6000mah battery and DS181 chip to measure temperature...
Hi,
When I start the TX sweep test with all 80 channels I get only 10 channels used by the RF.
Also power strength of the channels is modulated.
cf. attached frequency...
Hi
I am developing an iOS app that needs to communicate to an nrf51822(working in ble peripheral mode). The peripheral to which the app connect is selected using mac address...
hi nordic team：
I was wondering if the main program is too complex, and do not use the scheduler, and the connection parameter settings are correct. Whether because the...
Hello,
I have tested the DFU and everything works fine. Normaly the device enters into DFU mode with a pressed button 7, meaning the level on I/O 7 is LOW.
But in my...
Hi,
I've an HardFault, the program crash to the HardFault service routine at this row of the twi_hw_master.c:
--> NRF_PPI->CH[0].EEP = (uint32_t)&NRF_TWI1->EVENTS_BB;...
Hello, I am doing some dev on the NRF51822 with a Cortex MO manager. I have trouble on the MISO pin, and I am wondering if I have to drive this MISO pin by any kind of pull...
