Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I'm a little confused by the packet rate I'm getting on Gazell. Or rather I'm confused by the low number of 'timeouts' I'm seeing - I'd expect to see more, and would like...
Hi all,
in my custom board I'm using an NRF24L01+ as RF transceiver. The relevant part of schematic follow: (hi res => https://imgur.com/a/z4nQxXh )
The following...
The nRF905 chip can be setup to different payload length. 0-31 byte
Must RX and TX unit be setup to same payload length or can RX unit be setup to ex. 20 bytes and TX unit...
Hello.
There is a label on the back of the nRF9160DK.
I can find "HWID: FF:6A:B3:34:69:AC" on the label.
nRF connect can get the same string: " FF:6A:B3:34:69:AC " when...
I am trying eddystone example from SDK 15, its working fine but once I press the button to enable connecting and function nrf_ble_es_on_start_connectable_advertising(); is...
I want to use REG0 to supply 1.8v to external 4.7k pull-ups including when the system is off. Looking at the product specification REG0 can supply 1mA while in system off...
I have updated my repos to the latest commits on master for zephyr, mcuboot, nrf, and nrfxlib. I ran `
pip3 install -r scripts\requirements.txt
and I can open the asset_tracker...
hi, I'm working with NRF52832, DFU service is configured as secured. my question is : i'm trying to change dfu char a ct e ristic property to "ind i cation" by writing to...
Hello
I would like to test if provisioning over GATT Bearer still works with our application. Firstly I thought of using the serial example together with the PyACI, but...
Hardware: nRF52832
SDK 14.2
Segger Studio
Hello Sir or Madam,
We've made a new hardware variant of a previous design with an nRF52832 on much smaller form factor...
I use the QSPI(SDK15.2) of NRF52840 to read and write FLASH. Every time I open QSPI function, QSPI is closed after writing flash, but after close QSPI, there will be occasional...
Hi,
I want to capture data from TWI ADXL345 and send them by ble_nus_data_send() to mobile. Timing of data sending is done by application timer. My problem is that when...
Hi,
I tried to merge ble_app_multilink_central and ble_app_uart_c.
But, when I run the project It errors like below
I thougt the problem is the address of RAM_START...
